Dgcu165-5Bsb Parts

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This temperature control thermostat regulates your appliance's internal temperature by opening and closing the electrical circuit as conditions change, helping it reach and maintain the setting you select for consistent performance. What it does:

• Senses temperature and opens/closes contacts to control the system
• Helps maintain the set temperature by cycling the unit on and off
• Can lead to inconsistent temperature or a control knob that has no effect

• 1 temperature control thermostat

• Disconnect power before servicing; use proper PPE around sharp sheet metal
• Photograph wiring and transfer conductors one at a time to the new control
• Route it exactly as original and avoid kinks or sharp bends
• Set the control to mid-range after installation and allow the unit to stabilize before fine-tuning

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

Filter only. Fine filter not included.

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This dishwasher sump assembly houses the pump path and turbidity sensor that helps the machine detect water clarity for proper wash cycles. Replaces a worn or damaged sump to restore draining and turbidity sensing. What it does:

• Circulates and directs wash and drain water through the pump housing
• Houses the turbidity sensor that helps the control detect soil level for cycle adjustment
• Helps prevent leaks and maintains correct water flow for cleaning performance
• Can resolve symptoms like poor draining, error codes related to turbidity or water quality sensing, and reduced wash performance

• Disconnect power and water supply before attempting service; follow factory service instructions
• Inspect seals and mounting gaskets; replace any brittle or damaged gaskets to ensure a watertight fit
• Handle the turbidity sensor carefully and avoid contaminating the sensing surface

A small spring-style hose clamp that secures flexible tubing to fittings to help prevent leaks and hose separation. Replaces a worn or loose clamp to restore a tight seal on water and drain connections. What it does

• Compresses around a hose to hold it firmly on a barbed or smooth fitting
• Helps stop leaks and reduces chance of hose slip-off under pressure
• Commonly used on water, drain, and vent hoses where space is limited
• Simple, spring-action design keeps consistent tension as hoses expand/contract

• Disconnect power and shut off water supply before servicing appliance
• Use pliers to expand the clamp, slide into position, then release to seat it
• Inspect hose and fitting for damage; replace hose if cracked or brittle
• Do not overtighten or modify the clamp; replace with the exact style/size for a proper seal

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present

Replacement screw that secures trim, panels and internal components to restore proper fit and reduce rattling. Use when a fastener is missing, stripped, or corroded to help maintain stable, safe appliance operation. What it does:

• Secures panels, trim, brackets or other appliance parts to prevent looseness or movement.
• Replaces missing, worn, or damaged screws so components align and operate correctly.
• Helps reduce rattling, vibration noise, and gaps around doors or panels.
• Verify the exact size and thread before ordering to ensure proper fit.

• Disconnect power and water before starting any repair.
• Use the matching screw size and thread; do not force or overtighten.
• Start threads by hand to avoid cross-threading; use the correct screwdriver or bit.
• If threads or mounting holes are damaged, repair before reuse.

Electronic control board that manages the appliance's user interface, timing, and cycle logic. Replacing a failed board can restore responsive controls, display communication, and correct erratic or non-starting behavior. What it does:

• Manages user inputs, display signals, and command processing — symptoms: unresponsive buttons or blank/incorrect display.
• Controls cycle timing and sequence for motors, valves, and heaters — symptoms: unit won't start, stops mid-cycle, or won't advance cycles.
• Monitors sensors and error reporting — symptoms: persistent fault codes or incorrect cycle responses.

• Disconnect all power to the appliance before servicing to avoid shock or damage.
• Handle the board by its edges and use ESD precautions to protect electronic components.
• Compare the old board to the new one and transfer any required mounting hardware or harness connectors exactly as found.

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit