We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.
Replaced the top bearing assembly, drive belt, and blower wheel. The most time consuming and difficult part was putting the new drive belt back on the pulley and tensioner. Be sure to know how it is routed through them. It is a very tight fit getting your arm in there and connecting it blindly. Read more
Hi-limit thermostat. L210.
Great place to buy parts I can't say more than that Read more
Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
Fix a dryer that won't advance, runs continuously, or stops unexpectedly. This timer controls cycle progression and power routing. 15-minute DIY repair.
Just as the folks in the comments section said, I tested everything to make sure the timer had power which it did. I then tested with the OHM tester and saw that the switch was open when the timer was set to any drying cycle. So i changed the timer and voila! timer is functioning again. It was a very easy fix. Just pop the four screws out of the back of my timer panel on the dryer, detach all the wires, lift up on the little bracket that is holding the timer in place and twist it, and it... Read more
Exterior touch pad control panel for range hood. Mounts on the front of the unit. Replace when the fascia is cracked, broken, or worn to restore appearance.
I replaced all parts but the lights are still not working . I just talked to one of your technicians Shelly C, she was very helpful and had suggested some things for me to try to fix the lights , which I will . Read more
Dryer won't heat or overheating? The temperature switch controls heat settings. DIY-friendly repair—just swap wires and reassemble. Takes 20 minutes.
I unscrewed the 3 Phillips screws on the back of the dryer controls housing, then it folds forward for access to each control switch. the old one popped out, and I swapped the wires using a needle nose pliers, one by one, from the old switch to the new switch. The part was an exact fit, and popped right back into the housing. I screwed the 3 screws back in, pushed on the new knob, and it looks and works like new ! Read more
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more
Fix electrical grounding issues with this dryer ground strap assembly. Restores proper chassis grounding to reduce shock risk. Simple repair for worn connections.
Dryer won't heat or you smell gas? The gas valve controls fuel delivery to the burner. Common fix for heating failures and gas leaks. Moderate DIY repair.
Replaced. It Read more
This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.
Replaced the screw Read more
This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.
Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.
Converting your dryer from LP propane to natural gas? This conversion kit includes the orifice and components needed for a quick, straightforward swap.
Ordered the OEM conversion kit from you guys Read more
Replaces cracked or broken dryer control console back cover. Forms rear housing that supports timer, controls, and shields wiring. Easy DIY fix.
Ordered the faceplate and just for insurance a new switch and know. The installation required a phillips screwdriver, a needle nose pliers, and about 10 minutes of time. Thanks to AppliancePartsPros for getting me the right parts asap...........George Read more
Protective cover that shields the rear power connection terminals on your dryer. Replace if cracked, broken, or missing to prevent lint buildup and accidental contact with electrical connections.
About 45 minutes only because the actual line in the circuit breaker box was loose. It was nice because all the parts needed were suggested. The video was a great help. Thanks. Read more
This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does