Du810swpuo Parts

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Fix a dishwasher that won't drain or leaks from the pump area. This pump housing assembly replaces the seal connection between motor and tub. DIY repair.

This is a small sliding draw bar that connects to the upper detergent dispenser mechanism inside the dishwasher door. It helps actuate the dispenser lid so detergent is released at the correct point during the wash cycle. Replace this part if the detergent dispenser fails to open during a cycle or if the slide mechanism is cracked or broken.

Size: 7 foot long.

Secures the rack roller to the dishwasher tub wall for smooth gliding. Replace a cracked, broken, or loose mount to restore stable rack operation.

Screw: 8-16 x 3/8 inch.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Fix dishwasher overflows or won't fill issues. This water level float detects proper fill levels. Replaces broken or stuck floats causing drainage problems.

Color: white. Measures about 2-1/2 inches wide by 6 inches high by 10 inches deep.

Size: 8-18 x 1/2 inch.

Pronged cup washer for securing internal dishwasher components. Provides reliable retaining force for assembly hardware.

This is a gray plastic or metal channel that holds the door gasket in place along the edge of the dishwasher door or tub. It keeps the seal properly seated so the door closes tightly and prevents water from leaking out during wash cycles. Replace this retainer if the door gasket keeps slipping out of position or if you notice water leaking around the door.

This is the rinse aid dispenser assembly that mounts inside the dishwasher door and automatically releases rinse aid during the final rinse cycle. It helps prevent water spots and streaking on dishes by reducing surface tension on the water. Replace this part if rinse aid leaks prematurely, the dispenser cap won't stay closed, or your dishes come out spotted despite having rinse aid in the reservoir.