Du850swpq2 Whirlpool Parts

Size: 8-32 x 1/2 inch.

This black timer knob replaces a worn, cracked, or missing control knob so you can easily set the oven or range timer. Restores a positive grip and clear pointer for accurate timer adjustments. What it does:

• Fits onto the timer/control shaft to allow manual setting of the cook/timer function
• Replaces broken or stripped knobs that spin or won't engage the control
• Provides a visible pointer for precise timing and repeatable settings
• Improves user grip and control when turning the timer dial

• One black timer knob

• Power off the appliance before servicing electrical controls
• Pull the old knob straight off the shaft; align and push the new knob onto the splined shaft until fully seated
• Do not force the knob onto the shaft; verify correct spline alignment to avoid damage
• If the knob does not seat or the control shaft is damaged, inspect the control assembly and replace as needed

This seal collector is a molded collector seal that helps contain and direct water away from sensitive components, reducing leaks and moisture damage. It replaces a worn or cracked collector seal to restore normal water containment. What it does

• Channels and contains water at the tub/door interface to prevent leaks
• Replaces torn, hardened, or deformed seals that allow moisture escape
• Helps prevent water from reaching electrical components and undercarriage
• Commonly replaced when visible gaps, cracks, or persistent leaks are present

• One seal collector

• Disconnect power and water before starting any repair
• Access may require removing the door, kick panel, or access panels depending on model
• Inspect mating surfaces and clean debris before installing the new seal for proper fit

This is the tub funnel seal used to create a watertight connection at the washer tub funnel, helping prevent leaks and keep water flowing to the wash tub where it belongs. It replaces a worn, cracked or flattened seal. What it does:

• Creates a water-tight seal between the tub funnel and surrounding housing to prevent leaks
• Helps keep water directed into the wash tub during fill and drain cycles
• Worn or damaged seals can cause visible water around the top or cabinet and reduced containment
• Replacing a degraded seal restores proper sealing and reduces drip/leak symptoms

• Disconnect power and turn off water supply before starting any repair
• Remove the washer top/agitator or other access panels as required to reach the funnel area
• Inspect mating surfaces and clean away residue before seating the new seal for a proper fit
• Test with a short fill cycle to check for leaks after installation

This disk mount is a small replacement mounting disk that secures and aligns internal components so the appliance operates quietly and reliably. It restores proper fit where a worn or damaged mount causes misalignment or vibration. What it does:

• Provides a secure mounting point for internal assemblies and helps maintain correct component alignment
• Reduces vibration and rattling caused by a broken or deteriorated mount
• Supports stable operation and prevents excess wear on adjoining parts
• Commonly replaced when mount is cracked, warped, or missing

• One disk mount as shown

• Basic hand tools typically required; inspect surrounding components for damage before reassembly
• Disconnect power and/or gas and follow appliance safety procedures before starting work
• Retain all fasteners and observe correct orientation during installation

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This bearing helps the appliance's rotating assembly turn smoothly and reduces metal-on-metal wear for quieter, more reliable operation. Replace a worn bearing to address noise and movement issues that affect performance. What it does:

• Supports the drum or tub shaft so it rotates with minimal friction
• Reduces grinding, rumbling, or squeaking noises from the rotating assembly
• Helps prevent excessive wobble or vibration during spin cycles
• Limits metal wear that can lead to leaks or further component damage

• Disconnect power and water before starting work
• Inspect surrounding seals, shafts, and mounting surfaces for wear while replacing the bearing
• Use correct tools and replacement hardware; follow OEM instructions for torque and alignment