Dwhd770wfm/13 Parts

This is a tube-shaped actuator component used in the dishwasher's float switch assembly. It helps transmit the position of the float to the switch, which controls the water level inside the tub. Replace this part if the dishwasher is overfilling, not filling with water, or if the float mechanism feels loose or unresponsive.

This condensation tube routes moisture from the dryer's vented condensate tank to the drain, helping prevent leaks and pooling under the appliance. It's a direct-replacement tank drain tube for compatible vented-tank models. What it does:

• Channels condensate away from the tank to the dryer drain connection to reduce water buildup.
• Helps stop leaking or pooling beneath the dryer when the tank is vented.
• Restores proper condensate flow if the original tube is cracked, clogged, or damaged.
• Compatible with vented-tank dryer assemblies that use a routed drain tube for condensate.

• Turn off and unplug the dryer before starting any repair; if applicable, shut off gas supply.
• Remove access panels as needed to reach the condensate tank and tube; avoid damaging nearby wiring or hoses.
• Ensure tube fittings seat fully and secure clamps or fasteners to prevent leaks.

Secures threaded connections in your dishwasher to keep components tight and stable. Replace if cracked, stripped, or broken to restore proper fastening.

This shaped handle cap covers the end of a dishwasher door handle to restore a finished look and protect the handle connection. It keeps the door appearance consistent and hides the fastener area for a clean, finished fit. What it does:

• Replaces a damaged, cracked or missing handle end cap to restore appearance
• Covers and protects the handle mounting point from dirt and wear
• Prevents sharp edges or exposed fasteners on the door handle
• Matches the original profile so the handle closes and looks correct

• High-level replacement; may require removal of the door trim or handle screws—refer to your model's service instructions
• Disconnect power and water to the appliance before starting work to avoid injury
• Handle with care to avoid scratching painted surfaces; use appropriate trim tools if needed
• If fasteners are damaged, inspect and replace them with OEM-recommended hardware

Replacement adjuster socket for dishwasher leveling feet. Installs at cabinet base to raise or lower the unit for level installation. Replace if cracked or stripped.

Dishwasher won't start when door closes? This magnetic reed switch detects door position and signals the control. Simple 15-minute DIY replacement.

Dishwasher overfilling or won't stop filling? This float switch lever activates the water level sensor. Simple DIY fix restores proper fill control.

Secures tines to your dishwasher rack assembly. Replace this retaining clip if it's cracked, broken, or missing to keep rack tines properly positioned.

This is a sensor that detects the level or presence of rinse aid in the dishwasher's dispenser system. It communicates with the control board to ensure the correct amount of rinse aid is dispensed during the wash cycle for spot-free drying. Replace this sensor if your dishwasher displays a rinse-aid error, fails to dispense rinse aid, or consistently leaves spots and film on dishes despite a full rinse-aid reservoir.

Secures hoses to fittings, preventing leaks at connections. Replace when clamps lose tension or show corrosion. Confirm fit with your model number.

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.

Drain hose clamp

Fix detergent door that won't open or latch properly. This dispenser plunger actuator restores mechanical engagement between the lid and release mechanism.

M6 x 26 screw secures the dishwasher door tension adjuster assembly. Replace if screw is stripped, missing, or loose to restore proper door alignment.