Dwhd770wfp/18 Parts

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

This dishwasher door seal fits into the channel around the tub opening to create a tight, water-resistant barrier when the door closes. Replacing a worn seal helps stop leaks at the front of the unit and keeps cycles running efficiently. What it does:

• Forms a watertight perimeter seal between the tub and door
• Helps contain water and steam during wash and rinse cycles
• Aids proper door compression for reliable closing
• Common symptoms: water on the floor at the front, drips from door corners, visible cracks/flattening, or gaps in the gasket

• 1 door seal

• Disconnect power and turn off water supply before servicing
• Remove the old seal and clean the gasket channel thoroughly
• Start at the top center and press the new seal evenly into the groove without stretching
• Close the door to check for uniform compression, then run a short test cycle to inspect for leaks

Front leveling leg adjusts and supports your dishwasher at the front. Replace if damaged, missing, or worn to restore proper height and stability.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Trim strip that covers and protects dishwasher panel edges. Replace if cracked, loose, or missing to restore clean fit and prevent gaps. Confirm fit.

Secures hoses to fittings and prevents leaks in your dishwasher. Replace if stretched, corroded, or damaged to maintain a tight seal. Confirm fit.

Color: platinum gray. It measures about 2 inches wide by 2 inches high.

The Flip Tine Latch is an OEM part for Bosch dishwashers. It serves as a latching mechanism on upper dish racks that securely holds folded tines.

Made of durable plastic, the latch features offset hooks integrated along its base edge. These engage onto roll edges of individual flip up tines, pinning them neatly against the chamber to prevent unwanted movement.

Symptoms of a failed flip tine latch include:

• Sagging or unfolded flip tines potentially blocking spray jets
• Restricted water distribution due to improper rack orientation
• Scratched or misplaced dishes from unlatched tines potentially flailing
• Inefficient cleaning from lack of optimized spray coverage

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This flip tine insert clips into the dishwasher rack and provides adjustable support for dishes, bowls, and other items during the wash cycle. The tines fold down to create a flat surface for larger items or flip up to hold standard plates in place. Replace if the tines are broken, corroded, or no longer stay in position, causing dishes to shift during washing.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

This hinge cover is a molded trim piece that protects and conceals a refrigerator door hinge for a clean finished look. It helps keep hinge hardware free of dust and reduces sharp edges while restoring appearance. What it does

• Covers the door hinge area to hide hardware and improve the appliance's appearance
• Helps block dust and debris from accumulating on hinge components
• Reduces the risk of clothes or fingers catching on exposed hinge parts
• Matches OEM fit and shape to maintain proper clearance and alignment

• One hinge cover

• High-level replacement: remove the old cover and snap or screw the new cover into place (specific fasteners vary by model)
• Use basic hand tools if required; for model-specific instructions
• Disconnect power (or follow appliance-specific safety steps) before working near electrical components
• Inspect hinge and hardware while replacing the cover; replace damaged hinge components as needed

Washer that distributes load for screws connecting dishwasher handle components. Replace if cracked, worn, or missing to ensure secure handle mounting.

Protective base panel for dishwashers that covers internal components and provides a finished appearance. Replace if cracked, damaged, or discolored.