Ed5hhaxv002 Parts

This replacement washer is a small hardware spacer used in appliance assemblies. It provides a smooth bearing surface under a bolt or nut to distribute load and maintain proper spacing so components stay secure, aligned, and quiet.

• Distributes clamp load to protect mating parts and prevent loosening
• Maintains proper spacing/clearance for correct alignment
• Helps reduce wobble, scraping, or vibration when the original washer is worn or missing
• Visual signs include distortion, cracks, corrosion, or a fastener that no longer tightens securely

• Disconnect power before servicing; for laundry or dishwashing products, also shut off the water supply
• Note the original hardware stack-up and orientation; install the new washer in the same position
• Inspect the bolt/nut and mating surfaces; replace any damaged hardware and tighten per manufacturer guidance
• After reassembly, run a brief test and check for unusual noise or movement

Color: Black

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

Screw: 8-16 x 3/8 inch.

This replacement screw secures appliance panels, brackets, and components. Using the correct size restores a snug fit to reduce vibration, prevent loosening, and keep assemblies properly aligned during operation. What it does:

• Fastens sheet metal and component brackets in designated locations
• Replaces missing, stripped, or corroded hardware
• Helps eliminate rattling and vibration from loose panels
• Maintains proper alignment of covers and assemblies

• 1 screw

• Disconnect electrical power; shut off water or gas supplies if applicable
• Match length/thread to the original; replace one fastener at a time to preserve alignment
• Start by hand to avoid cross-threading; use the correct driver size
• Snug firmly but do not overtighten to prevent stripping

This replacement wiper is the OEM-style rubber blade that clears residue from a sealing surface to help restore proper closure and reduce moisture buildup. Install to replace torn, cracked, or worn wiper material for better sealing performance. What it does:

• Wipes water and debris from the seal or track to help maintain a tight closure.
• Reduces leaks, moisture accumulation, and related odors or frost build-up.
• Stops rubbing or improper closing caused by a damaged or missing wiper.
• Restores the intended contact between the seal and mating surface for reliable performance.

• Disconnect power and follow the appliance manufacturer's safety instructions before servicing.
• Typically installs by sliding or snapping into the wiper channel; use care to avoid stretching or tearing the rubber.
• Clean the mating surface and inspect the retainer or track for damage before installing; replace any damaged retainers per OEM instructions.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This replacement blade is the rotating element used within the appliance assembly to deliver the intended action. Installing a new blade restores smooth, efficient operation when the original is cracked, bent, worn, or missing.

• Provides the mechanical action required by the assembly (rotation/agitation)
• Helps maintain consistent performance and smooth operation
• Common failure signs: rattling or scraping noises, vibration/wobble
• Other symptoms: reduced performance in that section of the appliance, visible chips, cracks, or deformation

• Disconnect power before servicing; turn off water supply if applicable
• Wear cut-resistant gloves; edges may be sharp
• Note the original blade's orientation and spacing before removal; install the new blade the same way
• Hand-rotate after installation to ensure free movement and clearance before restoring power

This flipper spring returns the refrigerator's ice dispenser door (chute flapper) to the closed position after dispensing. It helps keep warm air and moisture out to minimize frost at the chute and reduce ice clumping in the bin.

• Provides the closing tension for the ice chute door/flapper
• Helps maintain a proper seal at the dispenser opening
• If worn or broken, you may notice the flapper not closing fully
• Frost/condensation around the chute or ice clumping in the bucket may occur

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control to access the ice chute door assembly; note spring orientation and anchor points
• Install the new spring in the same orientation; the flapper moves freely and closes under spring tension
• Wear gloves and use caution—metal edges in the dispenser area can be sharp

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Color: White

Replacement wire harness that restores electrical connections between the appliance control, power and components for reliable operation and correct signaling. Use this complete wiring assembly when damaged wires or connectors cause power or control issues. What it does:

• Routes power and signal conductors between the control board, switches, motors and sensors.
• Replaces damaged, frayed or melted wiring and broken connectors that can cause intermittent operation, no-start or control failures.
• Restores factory-style plug connections and routing to help prevent miswiring and shorts.
• Matches the original connector shapes and wire colors for straightforward replacement.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Remove and replace the harness by disconnecting connectors at the control and components; handle connectors by the plastic bodies, not the wires.
• Route the harness along the original path and secure with existing clips or fasteners to prevent rubbing or heat exposure.

This small rubber grommet cushions and supports a fan motor, helping reduce vibration and noise while the appliance is running. It fits into the motor bracket to provide a snug, insulated mounting point.

• Isolates fan motor vibration to cut rattling or buzzing
• Helps keep the motor aligned in its bracket
• Can wear, crack, or compress over time, causing vibration or noise
• Replacing a deteriorated grommet restores smooth, quieter operation

• Disconnect power before servicing
• Access the fan assembly and support the motor to relieve strain
• Note grommet orientation; transfer any sleeves or hardware as found
• Seat the new grommet fully in the bracket before remounting the motor

This door shelf trim (retainer bar) snaps across the front of a refrigerator door bin to keep bottles and condiments secure. Replace a cracked or missing rail to restore safe storage and prevent items from falling when the door opens.

• Secures items on the door shelf/bin and helps prevent spills during normal use
• Replaces broken, cracked, warped, or missing trim that won't stay attached
• Helps the door close without interference from loose items
• Typical symptoms: items fall from the door bin; rail is loose, damaged, or missing

• Empty the door bin before servicing
• Release the old trim by disengaging the end tabs or clips; pull outward to remove
• Align the new trim with the bin slots and snap both ends in evenly—do not overflex
• Inspect the door bin for cracks or worn slots that could prevent a secure fit

This end cap fits on the end of an appliance handle to restore a finished appearance and protect exposed hardware. It replaces cracked, broken, or missing handle trim to help prevent snags and improve overall fit and finish. What it does:

• Covers and protects the exposed end of a handle for a clean, finished look.
• Helps secure handle trim and maintain proper alignment at the handle end.
• Addresses symptoms like visible cracks, missing trim, loose or wobbling handle ends, and snagging on clothing.
• Cosmetic replacement only — restores appearance and prevents further wear to the handle area.

• Disconnect power or unplug the appliance before attempting any repair.
• Basic hand tools are typically required; the cap usually snaps or fits over the handle end or is retained by the original fasteners.
• Reuse original screws/retainers when possible; do not overtighten replacement fasteners.