Edsvhfxv008 Parts

This adjustment kit provides the factory components used to fine-tune alignment on the specified assembly. It helps restore proper fit and smooth operation when parts have shifted from wear, installation, or routine service.

• Provides manufacturer-specified hardware to adjust alignment and clearances
• Helps address uneven gaps, rubbing/binding, or poor fit
• Supports smooth operation by setting proper spacing and level
• Used during installation or after component replacement when alignment changes

• Disconnect power before servicing; shut off water or gas supply if applicable
• Refer to your model's service/installation instructions for adjustment points and sequence
• Mark original positions and take photos to aid reassembly
• Tighten fasteners securely, verify clearances, and test operation after adjustments

If your dishwasher won't start or stops mid-cycle, a faulty door lock may be the cause. This safety component secures the door during wash cycles.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.

Color: Black

Dishwasher rack stop prevents loaded dishes from shifting forward during wash cycles. Replace if cracked, broken, or missing to secure dishrack position.

Flexible water hose that routes water between dishwasher internal components. Replace if cracked, worn, or leaking to restore proper flow and prevent damage.

Secures hoses, wiring, and panels to reduce rattling in your dishwasher. Replace when worn or missing for quieter operation. Confirm fit with your model.

Replacement sensor assembly that detects appliance operating conditions and sends readings to the control system for proper operation. Installing a working sensor restores reliable feedback and helps resolve related error codes or inconsistent performance. What it does:

• Detects operating conditions and provides electrical feedback to the appliance control.
• Enables the control board to monitor and adjust cycles based on measured readings.
• Faulty or intermittent sensors can cause incorrect readings, error codes, or unstable/incorrect appliance operation.
• Replacing a failed sensor restores accurate sensing and helps return the appliance to normal function.

• Always disconnect power to the appliance before starting work to avoid shock or injury.
• Handle the sensor and wiring gently; avoid pulling on wires or bending sensor probes sharply.
• Ensure connectors are fully seated and routed clear of moving parts or heat sources.
• After installation, restore power and verify proper operation and that any previous error codes are cleared.

Small mounting clip that secures panels and trim on your dishwasher. Replace if your original clip is cracked, broken, or missing to keep exterior parts aligned.

This is the upper spray arm assembly that rotates beneath the top rack of the dishwasher, distributing water to clean dishes on the upper level. It connects to the water supply through a hub in the center of the dishwasher tub. Replace this spray arm if dishes on the top rack are not getting clean, if the arm is cracked or clogged, or if it no longer spins freely.

Fix leaking connections in your dishwasher with this rubber o-ring seal. Prevents water damage at valve, hose, and fitting joints. Simple repair.

Replacement mounting nut for dishwashers. Secures internal components in place. Order a new nut if yours is stripped, cracked, or missing.

The Tubing is an OEM part for Frigidaire dishwashers. As a key component of the spray arm assembly, the tubing works to distribute water throughout the dish rack during wash and rinse cycles. 

Causes of bad tubing can include mineral or limescale buildup reducing water pressure over time. Cracks or kinks from constant bending also jeopardize tubing integrity.

Symptoms of damaged tubing include:

• Poor or uneven spray pattern across the dish rack
• Reduced water pressure noticed during cycles  
• Leaks at tubing connections

Replacing the tubing restores the proper water flow needed for thorough cleaning. This OEM Frigidaire part replaces both the tubing segment and needed clamps/fasteners for hassle-free installation. It is also compatible with dishwasher models by Westinghouse, Crosley, and KitchenAid.

Dishwasher won't power on or has intermittent electrical issues? The main wiring harness connects control and power circuits. Moderate DIY repair.

Exterior side trim strip that covers and protects dishwasher cabinet edges. Replace worn, damaged, or missing trim to restore a finished appearance.