Ef368ca Parts

This wire harness connects the freezer/fresh-food control assembly to the refrigerator's wiring, restoring proper signal and power routing so controls and sensors communicate reliably. Designed to replace a damaged or worn control harness. What it does:

• Routes power and signal between the freezer/fresh-food control board and connected components
• Restores communication to sensors, switches, and control circuits
• Common symptom: control errors, intermittent cooling, or non-responsive controls when harness is damaged
• Prevents intermittent connections caused by frayed wires, broken terminals, or loose plugs

• Disconnect power to the appliance before attempting any repair
• Handle connectors and terminals carefully to avoid bending pins or causing additional damage
• Route harness along original wire paths and secure with existing clips or ties; avoid sharp edges and heat sources

This funnel directs water into the ice maker fill cup to ensure proper filling and reduce spills. It helps maintain reliable ice production by guiding water flow to the correct inlet area. What it does:

• Directs incoming water into the ice maker's fill cup so the correct amount reaches the ice mold
• Reduces splashing and overflow during the fill cycle
• Helps prevent water from pooling inside the freezer compartment near the ice maker
• Supports consistent ice production when installed and aligned properly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove the ice maker or access panel as needed to reach the old funnel
• Align the replacement funnel with the mounting tabs and secure per OEM orientation; avoid forcing it into place
• Test fill cycle after installation and check for leaks; for detailed steps

This body-side spacer installs on the cabinet side of the door or lid hardware. It sets the correct stand-off and alignment so the handle or latch feels solid and sits flush for a clean, secure fit. What it does:

• Positions and supports door/lid hardware on the cabinet/body side
• Maintains proper spacing to help prevent rubbing or scuffing of the panel
• Helps keep the handle or latch tight and aligned
• Common symptoms: loose or wobbly handle/latch, uneven alignment, visible gap or scuff marks at the mounting point

• Includes 1 body-side spacer

• Disconnect power to the appliance before servicing
• Support the handle/latch, remove the cabinet-side mounting screws, place the spacer, realign hardware, and reinstall screws snugly
• Reuse the original fasteners; avoid overtightening to prevent cracking the spacer or stripping threads
• Check door operation and alignment before finishing

This cover-tube protects and guides the evaporator/related tubing inside the freezer compartment to help maintain proper airflow and prevent contact damage. It's a direct-fit replacement used in affected Whirlpool refrigeration units. What it does:

• Protects evaporator or refrigerant lines from rubbing, kinking, or accidental contact
• Helps keep tubing routed properly for consistent airflow and cooling performance
• Reduces risk of damage during routine use and service
• Useful when replacing damaged, cracked, or missing tube covers

• Install by sliding or snapping into place per the factory diagram; no adhesives unless specified by OEM
• Power off and unplug the appliance before accessing internal components
• Handle surrounding tubing and evaporator fins carefully to avoid damage

This top hinge assembly secures and guides the refrigerator door at the cabinet top, restoring correct alignment for smooth opening and closing. Replace a worn or bent hinge to stop door sagging and improper sealing. What it does

• Supports the top of the refrigerator door and provides the pivot point for normal door movement
• Restores proper door alignment to prevent rubbing, gaps, and poor seal
• Reduces stress on the door and lower hinges caused by a bent or damaged top hinge
• Helps stop wind-up or binding when opening or closing the door

• Disconnect power and empty/secure the door before removing hinge fasteners to prevent injury or damage
• Support the door while replacing the hinge; two-person lift recommended for heavy doors
• Reuse or replace any hinge shims/screws only if explicitly specified by your model's parts list
• After installation, confirm door alignment and gasket seal; make minor adjustments as needed

This OEM grease is a purpose-made appliance lubricant that reduces friction and protects moving parts for smoother operation and longer component life. Use where specified by the manufacturer for bearings, slides, or motor shafts. What it does:

• Lubricates gears, bearings, rollers and shafts to reduce wear and noise
• Helps prevent binding, seizing, and grinding on moving components
• Protects metal parts from corrosion where grease is specified
• Keeps parts moving smoothly under normal operating temperatures

• Disconnect power before servicing any appliance; follow manufacturer service instructions
• Apply sparingly to clean, dry surfaces; avoid over-greasing which can attract debris
• Wear gloves and wipe excess grease from surrounding areas to prevent staining

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

This freezer light module housing secures and positions the freezer lamp assembly so the interior light stays protected and correctly aimed. It replaces a worn, cracked, or broken housing to restore proper lighting and fit. What it does:

• Holds the freezer light bulb and socket in place so the lamp illuminates the compartment
• Protects the lamp from moisture and physical damage
• Helps maintain correct light orientation for even interior lighting
• Commonly replaced when the housing cracks, breaks, or no longer secures the bulb

• Disconnect power (unplug or switch off breaker) before servicing the appliance.
• Handle the lamp/socket carefully; avoid forcing clips or tabs during removal and installation.
• If replacing the bulb or socket, verify correct bulb type separately—this listing is for the housing only.

This replacement shim is a thin positioning spacer used to align or level internal components for correct fit and operation. It helps restore proper clearances and reduce rubbing, noise, or misalignment-related issues. What it does:

• Provides precise spacing between parts to ensure correct alignment
• Helps eliminate rubbing or contact that can cause noise or wear
• Restores proper component clearance after service or reassembly
• Used when a missing, worn, or incorrect spacer leads to misalignment symptoms

• One replacement shim

• Inspect mating surfaces and clean debris before installing the shim
• Verify correct placement and orientation against the original shim or diagram
• Tighten fasteners to the manufacturer's specifications; do not overtighten
• Disconnect power and follow all safety precautions before servicing

Sealer for refrigerant line insulation.

Original Frigidaire Part.

This condenser grommet cushions and secures the refrigerator condenser assembly, reducing vibration and preventing metal-to-metal contact. It helps keep the condenser stable for quieter operation and longer component life. What it does:

• Isolates condenser from the cabinet to reduce rattling and vibration noise
• Prevents condenser edges from rubbing or wearing against the chassis
• Helps maintain proper condenser alignment for efficient airflow
• Commonly replaced when cracked, torn, or missing and causing noise or movement

• Disconnect power before servicing the appliance.
• Support the condenser assembly before removing or installing the grommet to avoid stress on tubing.
• Push the grommet into position; replace any grommets that are brittle or deformed.

This water tank cover replaces a damaged or missing upper reservoir cover to keep the appliance's water reservoir contained and protected. It restores a proper seal and helps prevent water from spilling into internal compartments. What it does:

• Covers and protects the water reservoir to reduce leaks and water intrusion
• Helps maintain correct water flow paths inside the cabinet
• Prevents debris from entering the tank and affecting performance
• Reduces risk of water contacting electrical components or insulation

• One water tank cover

• Designed for drop-in or snap-in replacement; follow OEM diagram for orientation
• Disconnect power and water supply before servicing to avoid shock and leakage
• Inspect adjoining gaskets and mounting clips; replace if cracked or missing
• Handle plastic parts gently to avoid cracking; use appropriate tools to remove fasteners

This is a genuine replacement mounting screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening where a damaged or missing screw causes loose panels or rattling. What it does:

• Secures panels, brackets, or internal parts to restore a tight fit
• Stops vibration-related noise caused by loose fasteners
• Replaces stripped, damaged, or missing screws for safe operation
• Matches the OEM thread and head style for correct fit and torque

• Use the matching screwdriver or driver bit to avoid cam-out or head damage
• Hand-start the screw to align parts before final tightening
• Do not overtighten; stop when parts are snug to avoid stripping threads
• Disconnect power to the appliance before accessing internal panels

This is a replacement screw fastener used to secure appliance components and panels. It restores proper fastening and helps stop loose parts from vibrating or shifting during operation. What it does:

• Secures panels, brackets, or components in place to maintain appliance stability
• Stops rattling, vibration noise, and intermittent contact caused by loose fasteners
• Restores proper alignment where original screws have stripped, corroded, or been lost
• Functions as a direct-fit hardware replacement when the OEM screw is needed

• One replacement screw (quantity: 1)

• Use appropriate driver and moderate torque to avoid stripping threads or damaging parts
• Disconnect power and follow appliance safety procedures before working on the unit
• Repair or replace the mating component as needed

This mounting bracket secures internal components to the appliance chassis to keep parts aligned and reduce movement during operation. It restores stable support so attached parts function reliably and quietly. What it does:

• Secures a component or assembly to the appliance frame to prevent shifting or sagging
• Maintains proper alignment of parts for reliable operation
• Helps reduce vibration and noise caused by loose or unsupported components
• Worn or broken brackets can cause rattling, misalignment, or intermittent part failures

• One mounting bracket

• Disconnect power before servicing to avoid electrical shock
• Use appropriate hand tools; keep fasteners for reinstallation unless new ones are specified
• Inspect surrounding components and mounting hardware; replace any stripped or damaged screws