Efls627uiw Parts

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

The Suspension Spring Bushing is an OEM part for Frigidaire washing machines. This part aids the suspension springs in absorbing vibrations and stabilizing the tub during operation. The bushings ensure that the movement is smooth and the noise levels are minimized.

Causes of a bad suspension spring bushing can include regular wear and tear from the constant load and movement, material fatigue, or improper installation that may accelerate deterioration. 

Symptoms of a bad suspension spring bushing include:

• Increased vibration or shaking of the washer, especially during the spin cycle
• Unusual noises like banging or thumping indicating the tub is not properly balanced
• Excessive movement or "walking" of the machine during use
• Wear and tear visible on the bushing, such as cracking or hardening of the material

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This cable tie secures wiring and small hoses to appliance frames and harnesses, keeping components organized and reducing wear from rubbing or vibration. It helps maintain safe routing so wires stay clear of moving or hot parts. What it does:

• Fastens wire bundles, harnesses, and small hoses to prevent movement
• Keeps wiring routed away from sharp edges and heat sources
• Reduces noise and wear caused by loose or vibrating wires
• Helps prevent chafing that can lead to insulation damage or intermittent connections

• Disconnect power before servicing electrical components
• Position ties to secure harnesses without over-tightening; trim excess tail
• Keep ties away from high-heat surfaces and moving parts
• Replace any damaged or brittle ties rather than reusing

This air chamber directs and channels cold air inside the appliance to help maintain even temperatures. Replacing a damaged or cracked air chamber restores proper airflow for more consistent cooling and performance. What it does:

• Channels conditioned air from the evaporator into the cabinet to help even temperature distribution
• Prevents air leaks and redirects airflow to the correct compartments
• Can cause uneven cooling, warm spots, or frost buildup when cracked or broken
• Works with fans and ducts to maintain proper airflow balance

• One air chamber assembly

• Disconnect power to the appliance before beginning service
• Remove interior panels or shelves as needed to access the chamber; handle plastic tabs and clips carefully to avoid breakage
• Inspect adjoining ducts, seals, and mounting tabs; replace any damaged components to ensure a proper seal

This is a motor-mount screw used to secure the appliance motor housing. It's a direct-fit fastener that restores proper motor attachment to reduce movement and rattling caused by loose or missing hardware. What it does:

• Secures the motor to its mounting bracket or housing
• Prevents motor shifting that can cause vibration, noise, or misalignment
• Restores proper mechanical connection after strip-out or lost hardware
• Helps maintain safe operation by keeping motor fastened

• Disconnect power before servicing the appliance.
• Use the correct screwdriver or socket to avoid stripping the head.
• Thread carefully and tighten to snug; avoid over-tightening which can strip threads.
• If mounting holes or threads are damaged, repair or replace the affected components before reinstalling.

This is a replacement mounting bracket that secures appliance panels and components, restoring proper alignment and stability. A direct-fit part that helps stop loose panels, rattling, or misalignment for safe, reliable operation. What it does:

• Provides a secure attachment point for panels, trim, or internal components
• Restores correct alignment to reduce rattling and vibration
• Prevents parts from shifting or coming loose during operation
• Re-establishes proper fit where a worn or broken bracket allows gaps

• One mounting bracket

• Install with appliance powered off and disconnected from power source
• Use appropriate fasteners and torque to avoid stripping or damage
• Inspect surrounding clips and hardware; replace any damaged fasteners

The Pulley Assembly is an OEM component specifically designed for Frigidaire front-loading washing machines. This assembly contains the plastic pulley wheel that works in conjunction with the belt drive system to power the agitator and basket movements. 

Symptoms of a faulty pulley include:

• Abnormal noises or squealing emitting from the area  
• Slipping or intermittent engagement of wash and spin functions
• Visible cracks or fractures in the pulley housing or wheel

Causes can be from wear of the drive belt slipping off track or tension malfunctions over extended use cycles. Repeated mechanical stress from propelling the heavy tub may also lead to structural fatigue cracks.

This OEM Frigidaire part is compatible with Electrolux, Gibson, Kelvinator, and Kenmore front-loading machines.

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This bushing is a small sleeve bearing that supports a rotating shaft and reduces metal-to-metal wear, helping restore smooth, quiet operation and proper alignment in the appliance. What it does:

• Supports and centers a rotating shaft or post to prevent wobble and friction
• Reduces wear between moving metal parts for smoother operation
• Helps stop squeaks, grinding noises, or rubbing caused by a worn support
• Restores proper alignment to improve component life and performance

• Disconnect power or unplug the appliance before starting any repair
• Inspect surrounding components and replace any visibly worn parts for best results
• Press or tap the bushing into place squarely; avoid deforming the sleeve during install

A simple wire-fastening cable tie that secures wiring and small hoses to prevent rubbing, snagging, or loose routing inside the appliance. Helps keep components organized for safer, quieter operation. What it does

• Secures wiring bundles and small hoses to chassis or brackets to prevent abrasion and movement
• Helps stop intermittent shorts or electrical noise caused by wires rubbing or contacting other parts
• Keeps airflow and moving parts clear by holding wiring away from fans and belts
• Useful when replacing or re-routing harnesses during repairs

• Always disconnect power before working on the appliance.
• Loop tie around wiring or hose, pull to secure snugly, and trim excess tail; do not overtighten.
• Replace ties that are brittle or damaged; use the same routing as the original harness.
• Dispose of trimmed ends and avoid sharp edges that could cut wiring insulation.

This genuine replacement screw secures appliance panels and components so they stay tightly mounted and aligned during normal use. It's a simple, direct fix when a loose or missing screw causes rattling or parts that won't stay in place. What it does:

• Replaces a stripped, damaged, or missing mounting screw used on trim, panels, or brackets
• Restores secure fastening to stop panel vibration, gaps, or rattling noises
• Matches OEM fit and fastening function for proper alignment
• Used where a short machine screw is required for cabinet or component attachment

• One screw

• Use the correct driver size to avoid stripping the head; turn until snug — do not overtighten
• Replace only the exact screw location and type called for in the service guide
• Disconnect power or follow appliance-specific safety steps if working near electrical or moving parts
• Replace all matching fasteners for even support

This control panel is the exterior console trim that secures and presents the refrigerator's user controls, restoring a finished appearance and protecting the internal switch assembly. It replaces cracked, warped, or cosmetically damaged panels. What it does:

• Covers and protects the control switches and display area from spills and debris
• Provides the finished bezel and button openings for the user interface
• Restores a clean, secure mounting surface if the original panel is cracked or loose
• Helps prevent accidental contact with internal wiring and components

• Disconnect power to the appliance before starting any work
• Remove any trim pieces or fasteners holding the old panel; handle gently to avoid chipping
• May require basic hand tools (screwdriver, nut driver); retain removed hardware for reassembly

The front panel clip is an OEM replacement part for Frigidaire washing machines. It is a small but crucial component that helps secure and hold the front panel or control panel in place on the washer. These clips are typically located at the top or sides of the front panel, snapping or clipping into place to provide a secure and stable fit.

Causes of a bad front panel clip can include physical damage from impact or mishandling, wear and tear over time, or exposure to moisture or excessive heat. A broken or missing clip can cause the front panel to become loose or detached, potentially affecting the proper functioning of the washer's controls or creating safety hazards.

Symptoms of a bad front panel clip include:

• The front panel feeling loose or unstable
• The panel not sitting flush against the washer body
• Difficulty in properly aligning or attaching the front panel
• Visible damage or missing clips

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore washer models.