Er30dsr Parts

This service window gasket seals the appliance door glass, keeping heat, moisture and lint inside for reliable performance and safer operation. It replaces a worn or damaged door seal to restore a proper fit and reduce air leaks. What it does:

• Seals the window-to-door interface so hot air and lint stay inside the cabinet
• Prevents steam and moisture escape that can affect drying performance
• Helps reduce noise and rattling caused by a loose or torn seal
• Visible damage, gaps, or persistent air leaks are common signs this part is needed

• Disconnect power (and gas if applicable) before starting any repair
• Replacement typically requires removing the door and carefully handling the glass
• Inspect mounting channel and fasteners; replace any damaged clips or screws

A replacement dryer door handle assembly that restores secure door opening and closing for affected dryer models. Replaces broken, cracked or loose handles so the door can latch and operate normally. What it does

• Replaces a damaged or worn dryer door handle so the door can open and close reliably.
• Helps stop handle wobble, cracking, or pieces breaking off during use.
• Addresses symptoms like a loose handle, handle that won't engage, or difficulty opening the dryer door.
• Works with the existing door latch and mounting points to restore normal operation.

• Disconnect power to the appliance before starting repairs to avoid electrical or injury hazards.
• Basic hand tools (screwdriver) are typically required; follow the appliance's service manual for access steps.
• Keep fasteners and mounting hardware organized.

This re-ignition module controls spark for gas surface burners and automatically re-sparks if the flame goes out, helping burners ignite consistently and stay lit when the original module has failed. What it does:

• Sends high-voltage pulses to the burner igniters to light gas
• Provides re-ignition if a burner flame is extinguished
• Distributes spark output to multiple burners as designed
• Common failure symptoms: no spark on all or most burners, continuous clicking, or intermittent ignition across burners

• 1 re-ignition module

• Disconnect electrical power at the breaker and shut off gas supply before servicing
• Access location varies by model; remove rear cover or top as required
• Label and transfer each wire one at a time; mount the module securely and route wires away from heat
• After installation, test each burner for proper ignition and that clicking stops once flame is established

An illuminated control knob that replaces a worn or missing knob on compatible cooking appliances. It restores smooth, accurate control and provides a clear, lighted indicator at the knob so settings are easy to confirm.

• Provides the interface to turn and set the control valve or switch
• Integrated light window works with the appliance's lighting circuit to indicate operation
• Direct replacement for cracked, stripped, loose, or missing knobs
• Symptoms include slipping/spinning on the shaft, difficulty adjusting settings, or a damaged knob cap or lens

• Disconnect power to the appliance before servicing; shut off gas supply if applicable
• Pull the old knob straight off the control stem—do not twist the stem
• Align the new knob with the stem and press firmly until fully seated
• If your model uses a lighting lead in the knob, transfer/connect it per the service manual

The Halogen Light Assembly is an OEM part for Samsung ovens. It provides illumination within the oven cavity, allowing you to easily monitor the cooking progress of your dishes.

A bad halogen light assembly can be caused by electrical issues, component failure, or damage to the bulb or socket. When the light assembly malfunctions, it can result in a range of problems, such as no light being emitted, flickering light, or the bulb not turning on at all.

Symptoms of a bad halogen light assembly include:

• No light emitted from the oven cavity
• Flickering light or poor illumination
• Bulb not turning on when the oven is in use
• Error codes displayed on the control panel

Replace your faulty halogen light assembly with this genuine OEM part to restore your oven. This Samsung part can also be used on Kenmore/Sears appliances. 
 

This replacement oven rack restores a stable cooking surface for slide-in and built-in ranges, letting cookware sit level for even baking and broiling. Durable wire construction resists warping under normal oven temperatures. What it does:

• Replaces a bent, warped or missing oven rack to restore safe, even cooking
• Provides a stable platform for pans, baking sheets and cookware
• Slides in and out on factory rack supports for easy access to food
• Resists heat exposure and typical wear from regular use

• No special tools required; rack slides into existing oven supports
• Ensure oven is completely cool before installing or handling
• If rack does not seat properly, support rails are undamaged and aligned
• Follow oven manufacturer's safety warnings and disconnect power if servicing nearby components

This LED isolator board supplies and protects the LED lighting/display circuitry on compatible Samsung appliances. It restores proper LED operation by isolating and regulating the LED power feed for reliable lighting and display performance. What it does:

• Routes and isolates power specifically for LED modules and display LEDs
• Helps stop LED flicker, dimming, or intermittent lighting caused by a failing isolator board
• Supports stable LED backlight and control signals to the appliance display
• Serves as a direct replacement for the original service board when the LED circuit is at fault

• One LED isolator/service board (DE81-06682A)

• Disconnect all power to the appliance before starting any repairs
• Handle the PCB by its edges and avoid static-sensitive contact with components
• Verify correct board orientation and connector seating during installation

This burner base assembly replaces the oven's damaged or worn burner base to restore stable combustion and proper heat distribution for gas ranges. It fits original equipment configurations and mounts where the burner connects to the range. What it does:

• Provides the appliance's burner mounting and gas flow interface for ignition
• Helps restore even flame pattern and consistent heating across the burner
• Replaces cracked, warped, or corroded burner bases that cause poor performance
• Can resolve ignition and flame stability issues when base damage is the cause

• Disconnect the appliance from gas and power before servicing.
• Use proper gas-line fittings and check all connections for leaks after installation.
• Inspect surrounding seals and gaskets; replace if damaged to maintain proper operation.

This service assembly secures and aligns the injector used in the appliance's dispensing/ice/water system, restoring proper positioning and reliable flow. Replace a damaged holder to stop misalignment that can cause leaks or intermittent dispensing. What it does:

• Holds and aligns the injector/nozzle in the dispenser or ice/water delivery path
• Keeps seals and hoses seated to prevent leaks and poor water flow
• Restores correct injector position when cracked, warped, or broken
• Helps resolve intermittent dispensing or dispenser misfeeds tied to misalignment

• Disconnect power and shut off water supply before beginning any repair
• Remove access panels and mounting fasteners to access the injector area; handle plastic clips gently to avoid breakage
• Inspect adjacent seals, hoses and the injector for damage; replace any worn parts as needed

This dual burner base assembly replaces the damaged or worn support that holds two cooktop burners in place, restoring proper alignment and stable burner seating for safer, more consistent heating. What it does

• Secures and centers two burner elements so they sit flat and stable
• Prevents burner wobble and misalignment that can cause uneven heating
• Provides the structural support for burners and related mounting hardware
• Works with original cooktop components to maintain proper burner positioning

• Disconnect power (and gas if applicable) to the appliance before starting work.
• Remove the cooktop or control panel per the manufacturer's service instructions to access the burner base.
• Inspect nearby components (burner caps, elements, clips) and replace any damaged parts for best results.

This regulator assembly controls LP gas pressure to the appliance's valve system, restoring correct burner and oven flame performance when the factory regulator is faulty. It helps ensure steady, adjustable gas flow for safe operation. What it does:

• Regulates LP gas pressure delivered to the appliance's valves and burners
• Can be used when burners have low, weak, or uneven flames
• Addresses issues where burners or oven fail to reach proper heat
• Supports proper gas delivery after conversion or regulator failure

• One regulator assembly (LP), 3/4 in

• Turn off gas supply and unplug the appliance before servicing
• Use proper gas fittings and thread sealant rated for gas; check for leaks after installation
• Tighten fittings securely but avoid over-torquing; follow OEM torque guidance if available

This upper oven broil element provides direct radiant heat for broiling and browning, restoring high-heat performance to the oven. Designed to match the OEM fit and function for affected Samsung ranges. What it does:

• Heats the top of the oven cavity for broiling, searing and browning
• Replaces a burnt, visibly damaged, or non-heating broil element
• Helps restore even top-down cooking when the broil function fails
• Works with factory mounting and terminal connections for an OEM-like replacement

• Disconnect power at the breaker before starting—this part connects to live AC terminals
• Handle carefully; sharp sheet-metal edges can be present inside the oven cavity
• Verify element terminals and mounting holes match your oven before final installation