Erde48 Parts

Replace worn oven door seals causing heat loss and uneven cooking. This thermocord windowpack fits between inner glass panels. Moderate DIY repair.

This replacement service door gasket restores the seal on an 18" refrigerator door to help maintain cold temperatures and reduce energy loss. It replaces a worn or torn gasket to improve cooling performance and prevent leaks. What it does:

• Seals the door edge to keep cold air in and warm air out
• Helps stop water or frost buildup around the door perimeter
• Reduces compressor run time caused by a failing seal
• Addresses symptoms like warm spots, condensation, or visible gasket damage

• Disconnect power to the appliance before starting any work
• Remove the old gasket carefully; keep track of any clips or screws
• Align the new gasket fully around the door frame and press into place; some models may require gentle warming or adhesive/clips
• Inspect the seal after installation and allow time for the gasket to form to the door

This service door gasket seals the refrigerator door edge to help maintain proper temperature and reduce moisture. It replaces a worn or damaged gasket to improve cold retention and reduce frost or condensation issues. What it does:

• Provides an airtight seal around a 36" refrigerator door edge
• Helps prevent warm air intrusion that can cause frost buildup or temperature instability
• Reduces condensation and improves cooling efficiency when the door closes properly
• Restores proper door contact and helps eliminate drafty or uneven sealing

• One service door gasket for a 36" refrigerator door

• Disconnect power to the appliance before starting any service
• Remove the old gasket carefully to avoid damaging the door flange; install the new gasket evenly around the perimeter
• Check that the gasket seats fully and that the door closes without obstruction; adjust hinge or strike if needed

Plastic insert snaps onto range leg to restore proper leveling and stability. Replace if cracked, worn, or missing to protect flooring and reduce vibration.

Porcelain-coated grill grate for select range and wall oven models. Replaces cracked, chipped, or worn grates. Installs over burner area.

This service nut retainer secures 1/4-20 service nuts used on panels and assemblies, keeping fasteners locked in place so parts stay aligned during use and maintenance. It's a low-profile clip designed for reliable holding where a captive nut is required. What it does:

• Captures and holds a 1/4-20 nut to provide a captive fastening point
• Keeps panels, brackets or components aligned while fasteners are installed
• Prevents nuts from falling into hard-to-reach areas during repair
• Helps reduce vibration looseness on secured assemblies

• Verify correct orientation and nut size (1/4-20) before installation
• Install with power off and disconnect appliance from power source
• May require basic hand tools; avoid forcing the retainer to prevent damage
• If hardware or mating clips are corroded or damaged, replace them together for best fit

This welded glass frame for the broiler door replaces a damaged or worn frame to restore the door's appearance and help the broiler seal and operate as intended. Fits into the broiler door assembly and supports the broiler glass. What it does:

• Replaces a cracked, warped, or separated broiler glass frame that can let heat escape or expose sharp edges
• Supports and secures the broiler glass panel inside the oven door assembly
• Restores proper alignment of the broiler glass for safer operation and better heat containment
• Helps prevent rattling or movement of the broiler glass during use

• One welded broiler glass frame

• Disconnect power and allow the appliance to cool completely before starting
• Handle glass edges carefully; wear protective gloves and eye protection
• Installation typically requires removing the broiler/oven door or door inner panel to access the frame

This service cover plate protects the range/stove manifold and valve area from debris and accidental contact, helping keep burner and valve components secure for reliable operation. What it does:

• Covers and shields the gas/electric manifold and valve assembly from dirt and spills
• Helps prevent accidental contact with controls and internal components
• Restores a finished appearance to the manifold area after service or repair
• Useful when replacing or servicing valves, burners or the manifold assembly

• Disconnect power and shut off gas supply before beginning work
• Remove any fasteners or adjacent trim panels to access manifold cover; reinstall fasteners securely
• Handle edges carefully to avoid cuts; use appropriate tools and OEM hardware
• Follow the appliance manufacturer's service manual for specific removal and reassembly steps