Ew23ca85ks2 Parts

Nylon

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This compressor inverter control board powers and regulates the variable-speed compressor in your refrigerator by converting household AC into the controlled output the compressor needs. Replacing a failed inverter can restore compressor operation and normal cooling performance.

• Receives commands from the main control to vary compressor speed for efficient, steady cooling
• Converts AC line voltage to the controlled output required by the compressor motor
• Common symptoms of failure: refrigerator warm, compressor not running while fans/lights operate
• May also present as intermittent cooling, clicking or humming near the compressor, or visible damage on the module

• Disconnect power before servicing; this is a high-voltage component mounted at the compressor
• Note wire positions and transfer connectors one at a time; ensure all connections are fully seated
• Secure the module to the original mounting to maintain proper heat dissipation and vibration control

This spacer fits between the fixed crusher blades inside the refrigerator's ice bucket assembly. It preserves the correct gap and alignment so the auger turns freely and crushed ice dispenses smoothly without jams or grinding.

• Maintains the correct spacing between fixed crusher blades in the ice bucket
• Keeps the blade stack and auger aligned for smooth rotation
• Helps prevent ice jams, grinding noises, and inconsistent crushed-ice output
• Replaces a worn, cracked, or missing spacer discovered during service

• Disconnect power before servicing; remove the ice bucket from the freezer door/bin
• Carefully disassemble the crusher housing, noting the exact order of blades, spacers, and washers
• Wear cut-resistant gloves; crusher blades are sharp
• Reassemble in the original sequence and verify the auger turns freely before reinstalling

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

This position-specific ice crusher blade (#1) fits inside the refrigerator's ice bucket assembly. It helps break up cubes into crushed ice; replacing a bent or worn blade restores consistent crushing and reduces jams or grinding noises during dispensing.

• Works with the auger and other numbered blades to crush ice when "Crush" is selected
• A bent, dull, or corroded blade can lead to no crushed ice, only cubes, slow dispensing, or scraping/grinding noises
• Restores even crushing and smoother auger rotation
• Position- and orientation-specific within the blade stack; match to your original

• Disconnect power and switch the ice maker OFF before servicing
• Remove and empty the ice bucket; allow any frost to thaw
• Disassemble the bucket front/auger and note the exact blade order and orientation—take photos for reference
• Wear cut-resistant gloves; reassemble blades, spacers, and washers exactly as removed and verify the auger turns freely before reinstalling

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

This ice crusher blade (#3) fits inside the refrigerator's ice bin crusher stack. It helps break cubes into crushed ice when selected, restoring smooth, consistent crushed-ice dispensing if the original blade is bent, dull, or missing. What it does:

• Works within the ice bin's crusher assembly to fracture cubes into crushed ice
• Engages with the auger and spacers as part of the blade stack
• Worn or damaged blades can lead to only cubes dispensing, weak crushing, jams, or scraping noises
• Visible bending, chips, or rust are common signs it needs replacement

• One crusher blade (#3)

• Disconnect power and remove the ice bin before service
• Empty the bin and carefully disassemble the crusher stack; note the exact order and orientation of blades, spacers, and washers
• Wear cut-resistant gloves—blade edges are sharp
• Reassemble in the same sequence and verify the assembly turns freely before reinstalling the bin and restoring power

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This hinge bearing supports the freezer door on the hinge pin so it swings smoothly and stays aligned. Replacing a worn bearing can stop scraping or sagging and help restore proper door movement and sealing.

• Provides a low-friction surface between the hinge pin and door
• Helps maintain correct door height and alignment for a reliable seal
• Wear symptoms include squeaking/scraping, door drop or wobble, and difficulty closing
• Replace if the original bearing is cracked, flattened, or missing

• Disconnect power and remove items from the freezer door before starting
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Slide the old bearing off the hinge pin and install the new bearing in the same orientation
• Reassemble, then check door alignment and gasket contact; adjust as needed

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle