Ewdw6505gso Parts

Replacement latch assembly that secures the appliance door for reliable closure and operation. Restores proper latch engagement so the door stays closed during cycles and reduces the chance of accidental openings. What it does:

• Physically secures and releases the door by engaging the striker when closed.
• Replaces broken, worn, or loose latches that cause doors to not stay closed, pop open, or fail to engage.
• Helps restore consistent door operation and prevents interruptions during cycles.
• Works with the existing striker and door hardware when installed correctly.

• Disconnect power (or unplug the appliance) before beginning any service.
• Use appropriate hand tools; remove door trim or access panels as needed to reach the latch.
• Keep fasteners and small parts organized to ensure proper reassembly and alignment.
• Test the latch operation several times after installation.

This flexible door gasket replaces a worn refrigerator seal to help maintain a tight fridge/freezer seal and improve temperature stability. It restores proper door sealing to reduce energy loss and help prevent moisture buildup. What it does:

• Creates an airtight barrier between the door and cabinet to keep cold air in
• Helps reduce frost or ice buildup by limiting warm, moist air entry
• Prevents water pooling from condensation at the door edge
• Can eliminate drafts, noisy closing, or difficulty latching caused by a damaged seal

• One replacement door gasket

• Remove power to the appliance before starting and work with clean, dry hands
• Clean mounting surface and channel; gently warm the gasket if stiffness prevents seating
• Start at a corner and press the gasket evenly into the channel; check for full, continuous contact around the door

This lower dishwasher spray arm circulates water across the lower rack to help wash and rinse dishes effectively. Replaces a worn or damaged arm to restore proper spray coverage and improve cleaning performance. What it does:

• Rotates and distributes pressurized water to reach dishes on the lower rack
• Helps remove food soil and rinse detergent from dishes and cookware
• Commonly replaced when you notice poor cleaning, uneven spray, or a cracked/broken arm
• Also replaced if the arm no longer spins freely or leaks at the hub

• Disconnect power to the dishwasher and shut off water supply before starting
• Remove lower rack and any obstructions; follow OEM removal steps to detach the old arm
• Ensure the arm hub and spray ports are free of debris before installing the new arm
• Reinstall rack, restore power/water, and run a short cycle to confirm proper rotation and no leaks

This lower spray arm distributes pressurized water across the dishwasher's lower rack to help remove food and residue for cleaner dishes. It mounts on the hub beneath the lower rack and spins during the wash cycle. What it does:

• Directs rotating spray patterns to reach plates, pots and pans on the lower rack
• Helps clear stuck-on food and improve overall wash performance when functioning properly
• Can fail or clog from mineral deposits or trapped debris, causing reduced spray or poor cleaning
• Replacing a worn or cracked spray arm restores proper water flow and spray coverage

• Disconnect power and water to the dishwasher before starting any service
• Inspect the hub and fastener for damage; remove debris from spray holes and seals before installing
• Hand-thread or snap the arm into place per factory alignment; do not force or overtighten
• Run a short rinse cycle to check for proper rotation and leaks after installation

A small mounting/trim plate that secures and aligns nearby appliance components, restoring fit and preventing vibration or rubbing. Simple replacement helps stop rattles and keeps panels or assemblies seated correctly. What it does

• Secures and supports a nearby panel or component to its mounting point
• Keeps parts aligned to prevent binding, wear, or rubbing
• Reduces vibration and rattling caused by loose or missing hardware
• Restores proper fit and finish where a damaged or missing plate allowed gaps

• Disconnect power and/or water before starting work when applicable
• Use the original screws or equivalent size hardware; do not overtighten
• Verify orientation and fit before final tightening
• Replace rusted or damaged mounting fasteners to ensure a secure fit

This genuine replacement door gasket seals the refrigerator door to keep cold air inside and help maintain temperature control. Replacing a worn gasket restores proper sealing to reduce frost, leaks, and energy loss. What it does:

• Forms an airtight seal around the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and interior condensation by maintaining a consistent temperature
• Reduces energy use and prevents food spoilage caused by poor door sealing
• Fits into the door channel and compresses to create a tight, reliable seal

• For safety, unplug the appliance before starting any repair.
• Remove the old gasket by loosening screws/clips and pulling the gasket from the door channel; follow OEM instructions.
• Warm the new gasket or use a hair dryer to make it more pliable for easier installation and a snug fit.
• After installation, check for gaps and allow gasket to form to the door; avoid sharp tools that could damage the seal.

This flexible replacement hose routes water between appliance components to restore proper water flow and prevent leaks. It's a direct-fit service part when the original hose is cracked, split, or clogged. What it does:

• Carries water safely between the pump, valve, tank or dispenser as designed
• Restores proper drainage or water delivery when the original hose is leaking or collapsed
• Prevents water damage by replacing worn, brittle, or pinched tubing
• Helps eliminate noises and poor performance caused by restricted flow

• One replacement flexible hose

• Disconnect power and shut off the water supply before beginning any work
• Use appropriate clamps or fittings; tighten to manufacturer torque recommendations without over-tightening
• Inspect connections and run a water test after installation to check for leaks

This replacement refrigerator water supply hose routes water between the house line, valve and dispenser/ice system to restore reliable water flow and prevent leaks. It's a direct-fit service part when the original hose is damaged or leaking. What it does:

• Carries water from the inlet/valve to the dispenser or ice-making components
• Stops leaks and drips caused by cracked, pinched, or deteriorated tubing
• Restores steady water flow for filling ice makers or dispensing water
• Helps eliminate pooling or low-flow symptoms at the dispenser/ice maker

• Turn off the refrigerator and shut off the home water supply before installing
• Inspect fittings and seals; replace clamps or gaskets if worn to ensure a watertight connection
• Tighten connections securely but avoid overtightening plastic fittings

A replacement switch assembly that restores proper electrical control for compatible Frigidaire appliances. Replaces a worn or faulty switch to help restore reliable on/off and cycle control for the affected function. What it does:

• Acts as the electrical on/off or selector switch for the appliance control circuit
• Restores reliable contact when original switch is intermittent or unresponsive
• Commonly used when the appliance won't start, specific functions won't engage, or controls feel loose
• Fits into the original control panel location and connects to existing wiring harness

• Disconnect power (unplug appliance or switch off breaker) before inspecting or replacing the switch
• Access may require removing a control panel or trim—keep fasteners and wiring orientation noted
• Handle terminals carefully to avoid bending or damaging contacts; confirm secure wiring connections before restoring power

This wiring harness provides the electrical connection between control components, delivering secure signal and power routing for proper appliance operation. Replaces a worn or damaged harness to restore reliable connections and control response. What it does

• Routes power and control signals between internal components so controls and motors can operate
• Restores connection when frayed wires or broken plugs cause intermittent or no power to controls
• Helps stop failures caused by loose, corroded, or damaged wiring connections
• Prevents electrical arcing and poor contact from damaged connectors

• Disconnect all power (unplug appliance or switch off breaker) before starting any repair
• Handle connectors and wires carefully; avoid pulling on individual wires when removing/installing
• Match connector shapes and pin counts; ensure secure, fully seated connections
• Refer to the wiring diagram for routing and connector locations

This float assembly helps detect and control water level inside the appliance to prevent overfilling and enable normal drain cycles. It replaces a worn or stuck float to restore reliable water sensing and operation. What it does:

• Rises with water level to trigger the appliance's water-level detection system
• Helps stop overfilling and reduces risk of leaks or continuous fill
• Commonly related to symptoms like persistent fill, frequent draining, or error codes tied to water level
• Works as the mechanical sensing element in the water management system

• One float assembly

• Disconnect power and water supply before starting any repair
• Verify correct alignment and free movement of the float after installation
• Reassemble panels and run a short test cycle to confirm proper operation

This cap is a small sealing cover that helps protect and close off an appliance connection or opening, restoring a finished appearance and helping prevent dirt or moisture intrusion. It's a simple replacement for worn or missing caps. What it does:

• Covers and seals small ports, openings, or fastener heads to block debris and moisture.
• Restores a secure fit where an original cap has cracked, broken, or gone missing.
• Helps maintain proper appliance operation by preventing contamination of components.
• Works as a cosmetic replacement to conceal exposed hardware.

• Disconnect power and shut off water before servicing the appliance.
• Inspect the mating surface for damage or residue; clean before installing the cap.
• Press or snap the cap into place; avoid excessive force or prying that can damage the part.
• Replace any damaged retaining clips or grommets as needed for a secure fit.

A small replacement retainer clip that secures interior components and trim to keep parts aligned and stable. Fits specified Frigidaire/WCI assemblies and restores proper fit where the original clip is worn or broken. What it does:

• Holds panels, trim, or small assemblies in position to prevent rattling or misalignment
• Helps maintain proper spacing between components for reliable operation
• Commonly used where a snap-in plastic or metal fastener has failed
• Can stop noise caused by loose interior parts

• One replacement clip

• Designed for snap-in installation; remove power and any obstructing panels before replacing
• Inspect surrounding mounting surface and mating features for damage before installing
• Use gentle pressure to seat the clip; do not force or bend surrounding parts