Ewmed70jsso Parts

This replacement latch secures an appliance door or drawer by engaging its mating strike so it stays closed during use. Restoring a worn latch helps ensure reliable closure and proper operation when the control checks for a closed position. What it does:

• Mechanically holds the door/drawer shut by engaging the strike/catch
• Helps the appliance recognize a closed condition for starting or continuing a cycle
• Addresses issues where the door/drawer won't stay closed or pops open
• Common symptoms include "door open" messages or cycles that won't start

• 1 latch

• Disconnect power before servicing; turn off water supply if working on a washer
• Use basic hand tools to remove the old latch and transfer any reusable screws/clips
• Align the new latch with the strike/catch for smooth engagement
• Close and test the door/drawer several times before running a cycle

Replace a cracked or cloudy door window with this outer lens. It forms the transparent exterior panel of the door, protecting the inner window and restoring a clean look and clear view into the drum during cycles.

• Forms the exterior, see-through panel of the door window
• Shields the inner window and helps the door close evenly against its trim
• Replace if the outer window is cracked, chipped, warped, loose, or discolored/cloudy
• Damage may cause poor visibility or sharp edges around the door opening

• Disconnect power before servicing the appliance
• Remove the door and place it on a padded surface
• Separate inner/outer door panels, note screw locations, and lift out the old lens
• Clean mating surfaces; set the new lens in place and reassemble without over-tightening screws

Replacement cover that restores the appliance's finished appearance while shielding internal components from dirt and accidental contact. Fits the original mounting points for a clean, factory look and safe operation. What it does

• Protects internal wiring and components from dust, spills, and accidental contact
• Restores the appliance's finished appearance when the original cover is cracked, broken, or missing
• Helps reduce noise from loose or exposed parts by holding components in place
• Prevents fingers and tools from reaching sensitive areas during normal use

• Disconnect power to the appliance before beginning any repair.
• Remove fasteners or release retaining tabs carefully to avoid breaking plastic clips.
• Align mounting tabs and secure with original hardware; do not force or over-tighten.
• If clips are damaged, replace them before reinstalling the cover.

This part is a genuine OEM replacement user interface control board intended for use with dryers. The user interface control board allows the user to choose the desired settings and processes the different dryer cycles, as well as housing the display. Over time, this part might become worn or faulty, requiring immediate replacement. If the user notices the error code E9B, it's a sign the control board needs replaced. Take caution and disconnect the dryer from the power source before attempting any repairs. Work gloves should be worn to prevent serious injuries.This part has been made by Frigidaire and has been sourced directly from the manufacturer. This user interface control board is sold individually. It is intended for use with dryers manufactured by Frigidaire, Electrolux, Gibson, Westinghouse, and other compatible brands.

This LED interior lamp assembly replaces a failed fridge light to restore bright, efficient illumination inside the appliance. Designed as a direct-fit replacement for the OEM lamp module, it improves visibility for food storage areas. What it does

• Provides bright, energy-efficient interior lighting for refrigerator compartments
• Replaces a non-working, flickering, or dim fridge light
• Fits into the existing light housing or module to restore normal illumination
• Helps you see contents clearly so you can find items faster

• One LED interior lamp assembly (single)

• Disconnect power to the appliance before starting any work
• Remove the light cover/diffuser per appliance instructions to access the lamp assembly
• Handle the lamp carefully and avoid forcing connectors; align and seat the module fully

This electrical wiring harness connects refrigerator components to restore reliable power and signal paths. It replaces a damaged or worn harness to help stop intermittent operation and return affected circuits to normal function. What it does:

• Routes power and control signals between components and the main control
• Restores connectivity when a frayed or broken wire causes intermittent or no operation
• Helps resolve symptoms such as non-working lights, controls, dispenser, or ice maker when caused by a failed harness
• Provides factory-style connector plugs for a direct replacement fit

• Disconnect power to the appliance before starting any work.
• Access may require removing interior panels or appliance trim; keep fasteners organized.
• Match connector shapes and colors; do not force connectors together.
• Inspect mounting points and secure harness to avoid contact with sharp edges or moving parts.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

This is a replacement push button that fits on the appliance control panel and restores tactile control for a single function. It provides a simple, direct way to replace a worn, loose, or missing button so controls are usable again. What it does

• Replaces a damaged, cracked, or missing control panel push button
• Restores a firm tactile surface for reliable pressing of a single function
• Helps stop intermittent or unregistered button presses caused by wear
• Keeps the control panel looking complete and prevents accidental contact with underlying switches

• One push button

• Disconnect power to the appliance before any service to avoid shock or injury
• Typically snaps into the front of the control panel or slides onto a stem; keep track of orientation
• If access requires removing the control panel, keep screws and small parts organized for reassembly

This trim ring is a replacement surface trim piece that restores the finished look and edge around the appliance opening. It provides a clean, secure edge and replaces bent, cracked, or missing trim to improve appearance and fit. What it does

• Covers and finishes the exposed edge of the appliance opening for a clean appearance
• Secures and aligns adjacent components by providing a stable mounting edge
• Addresses cosmetic damage such as dents, cracks, or paint loss around the opening
• Helps prevent small items from getting caught in the exposed edge

• One trim ring

• Disconnect power to the appliance before starting any repair
• Removal typically requires loosening mounting screws or clips; keep hardware for re-use unless damaged
• Handle edges carefully; part and surrounding metal may be sharp
• If the trim mounts to or around other components (elements, panels), support those parts during removal and reinstallation

Color: Silver

This retainer secures appliance panels and components to keep assemblies aligned and stable, restoring proper fit and reducing noise or vibration. Use when a clip or bracket has broken, come loose, or no longer holds parts in place. What it does:

• Holds trim, panels or internal components in position to prevent rattling and misalignment
• Replaces worn or broken clips that allow gaps or loose parts
• Helps restore a snug fit after service or component replacement
• Works as a simple fastener to maintain proper assembly alignment

• Disconnect power to the appliance before beginning any repair
• Installation typically requires basic hand tools; handle small clips carefully to avoid losing them
• Inspect surrounding clips and mounting points and replace any damaged hardware