Faf3801lwo Parts

This replacement door transition ring restores the trim and alignment where the appliance door meets the cabinet, helping the door close smoothly and improving the unit's appearance and seal. What it does

• Covers and protects the gap between the door and cabinet, preventing rubbing and wear on edges.
• Guides the door for consistent closing and helps reduce drafts or uneven sealing.
• Stops rattling or banging caused by worn or damaged trim pieces.
• Restores finished look to the door area when the original ring is cracked, broken, or missing.

• One door transition ring.

• Disconnect power (or unplug unit) before starting any work to avoid electrical or injury hazards.
• Most installs are snap-in or require removing the door or outer panel—use basic hand tools and avoid forcing parts.
• Handle the trim carefully to avoid cracking; replace any damaged fasteners or clips rather than reusing broken pieces.

This shock absorber mounts between the washer tub and frame to dampen motion and reduce vibration for smoother, quieter spin cycles. It helps stabilize the drum so loads stay balanced and wear on other suspension parts is minimized. What it does

• Dampens tub movement during agitation and spin to reduce shaking and noise
• Helps keep the drum centered so loads don't shift excessively
• Commonly used when the washer vibrates, bangs during spin, or the tub feels unstable
• Restores proper suspension performance to extend life of springs and mounts

• One shock absorber

• Disconnect power and water before starting; support the tub to prevent it from dropping when removing shocks
• Remove access panels as needed and replace shocks one at a time to keep the tub supported
• Use care with retaining clips/pins; transfer any clips or bushings from the old shock if required and install in the same orientation
• Test with a short spin after installation and re-check mounting hardware for tightness

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This bushing is a small sleeve bearing that supports a rotating shaft and reduces metal-to-metal wear, helping restore smooth, quiet operation and proper alignment in the appliance. What it does:

• Supports and centers a rotating shaft or post to prevent wobble and friction
• Reduces wear between moving metal parts for smoother operation
• Helps stop squeaks, grinding noises, or rubbing caused by a worn support
• Restores proper alignment to improve component life and performance

• Disconnect power or unplug the appliance before starting any repair
• Inspect surrounding components and replace any visibly worn parts for best results
• Press or tap the bushing into place squarely; avoid deforming the sleeve during install

This main electronic control board manages refrigerator functions and restores user control to the appliance. Replaces a failed board to return digital controls, cycles, and timed components to normal operation. What it does:

• Receives and processes user inputs from the control panel and directs functions like cooling cycles and defrost.
• Controls compressor, fans, and defrost timing so the refrigerator maintains proper temperature regulation.
• Powers and updates the display and user interface; often replaced when the display or buttons become unresponsive.
• Common symptom fix: intermittent or complete loss of control panel response, erratic cooling behavior, or failure to initiate defrost cycles.

• One main electronic control board

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Handle the board by the edges and avoid static discharge; wear an anti-static wrist strap if available.
• Verify connector orientation and seating before restoring power; do not force connectors.

A simple wire-fastening cable tie that secures wiring and small hoses to prevent rubbing, snagging, or loose routing inside the appliance. Helps keep components organized for safer, quieter operation. What it does

• Secures wiring bundles and small hoses to chassis or brackets to prevent abrasion and movement
• Helps stop intermittent shorts or electrical noise caused by wires rubbing or contacting other parts
• Keeps airflow and moving parts clear by holding wiring away from fans and belts
• Useful when replacing or re-routing harnesses during repairs

• Always disconnect power before working on the appliance.
• Loop tie around wiring or hose, pull to secure snugly, and trim excess tail; do not overtighten.
• Replace ties that are brittle or damaged; use the same routing as the original harness.
• Dispose of trimmed ends and avoid sharp edges that could cut wiring insulation.

Keep your washer protected during a move. This shipping bolt secures the washer's tub and suspension during transport. Replace missing bolts before relocating the appliance to help prevent vibration damage, leaks, and broken suspension components.

• Locks the tub assembly to minimize movement while the washer is shipped or relocated
• Helps prevent damage to shocks/suspension, outer tub, and hose connections during a move
• Use for transport only; remove all shipping/transit bolts before operating the washer
• If a move was done without shipping bolts, post-move symptoms may include excessive vibration, banging, or leaks

• Unplug the washer, shut off water, and drain/empty the unit before installing shipping hardware
• Refer to your model's installation guide for the required number and locations; install all shipping bolts specified for your model
• Tighten each bolt until snug; do not overtighten
• Remove all shipping bolts after relocation and keep them for future moves; never run the washer with shipping bolts installed

This replacement control panel restores the appliance's front console and user interface so buttons and the display work reliably. It provides the visible face and mounting surface for controls and status indicators. What it does:

• Houses the appliance's buttons, touchpads, and display area so you can select settings and see status
• Replaces cracked, scratched, or cosmetically damaged panels that affect appearance or button access
• Helps when buttons are unresponsive due to a damaged front panel
• Restores a clean mounting surface for switches and overlays

• Disconnect power before starting any repair to avoid shock or injury
• Remove trim, bezels, or mounting screws as needed to access the panel; keep fasteners for reassembly
• Handle carefully to avoid scratching or cracking; use proper tools to release clips

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This electronic control is the oven's main user interface and timing/temperature manager, restoring oven functions and display responsiveness for safe, reliable cooking. It replaces a failed control module to bring back normal oven operation. What it does:

• Manages oven temperature sensing, bake/broil cycles, timers and user commands
• Controls the oven display, clock, and front-panel touch/key inputs
• Stops oven heating or cancels cycles when internal control fails or shows errors
• Common symptom fixes: blank or unresponsive display, inaccurate temps, oven not starting, or error codes tied to the main control

• One electronic control assembly

• Disconnect power to the appliance before starting work to avoid shock or damage
• Handle the board carefully; avoid touching circuitry and use anti-static precautions when possible
• Some units may require front-panel reassembly or minor adjustments after swap;

This is a replacement bolt fastener that secures interior and exterior appliance components for stable operation and safe use. It restores proper fit where a worn or missing bolt causes looseness or rattling. What it does:

• Secures panels, brackets, or assemblies to prevent shifting and vibration
• Restores proper alignment for doors, drawers, or mounted components
• Helps stop rattling, squeaks, or visible gaps caused by a missing or damaged fastener
• Provides a durable connection when the original bolt is stripped, corroded, or lost

• One replacement bolt

• Use the correct size socket or wrench to avoid rounding the head
• Hand-start threads to prevent cross-threading; tighten until snug—do not overtighten
• Disconnect power and empty affected areas if working near electrical components or sharp edges
• Replace with the exact OEM bolt for best fit and function

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and keeping connections tight for reliable appliance operation. Use it where a compact, durable clamp is required for water or drain lines. What it does:

• Holds hoses or tubes firmly to inlet/outlet fittings to reduce leaks
• Prevents hoses from slipping off during normal use or vibration
• Helps maintain proper fluid flow by keeping connections sealed
• Useful for water lines, drain hoses, and small appliance tubing

• One clamp

• Turn off and unplug the appliance and shut off water supply before starting
• Inspect the hose and fitting; replace any damaged hose before installing clamp
• Position clamp over the hose/fitting and tighten evenly for a snug fit without crushing the hose