Fafw3574kao Parts

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

This user interface control board replaces the oven's front control module so you can send commands and view settings. It restores responsive touch/buttons and proper display feedback for normal operation. What it does

• Receives button/touch inputs and relays commands to the oven control system
• Provides display/status feedback so settings and timers are visible
• Helps resolve unresponsive buttons, blank or incorrect display readouts, or intermittent control behavior
• Works as the main input surface for oven functions like bake, broil, timers, and temperature settings

• One user interface control board (UI board) — only items explicitly listed by the manufacturer are included

• Turn power to the appliance off at the breaker before servicing to avoid electrical shock
• Handle the board and connectors carefully; avoid touching contacts or flexing the board
• Verify connector orientation and secure mounting; test operation with power restored

The Outside Door Panel replaces a cracked or broken outer trim on your washer door. It restores appearance and alignment, supporting the door glass and handle so the door latches correctly and cycles can start.

• Forms the exterior frame/trim and handle area of the washer door
• Supports and positions the door glass while aligning with the hinge and latch
• Helps ensure the door closes properly to allow a cycle to begin
• Typical symptoms: cracked/broken trim, loose or misaligned door, difficulty opening/closing

• Disconnect power; turn off water supplies before servicing
• Open the door and support the assembly; remove perimeter screws securing the outer to the inner door panel
• Transfer door glass, handle components, and any reusable hardware from the old panel to the new one
• Reassemble and tighten screws evenly; verify smooth operation and proper latching before use

This rubber grommet cushions and protects components by isolating vibration and preventing wear where parts pass through openings. It restores proper fit and reduces noise or rubbing caused by a worn or missing grommet. What it does:

• Cushions panels, housings, or shafts to reduce vibration and noise
• Protects wiring, hoses, or metal edges from abrasion where they pass through openings
• Keeps assemblies aligned by filling mounting gaps and securing components
• Common symptom: increased rattling, vibration, or chafing around the affected area

• One rubber grommet

• Disconnect power to the appliance before beginning any repair
• Remove panels or components as needed to access the grommet; hand tools may be sufficient
• Inspect surrounding parts and replace any damaged items
• Use the OEM-style grommet to ensure proper fit and function

This O-ring is a small rubber seal that helps prevent water or refrigerant leaks by creating a tight connection between mating parts. Replacing a worn O-ring restores a secure seal and reduces dripping or loss of pressure. What it does:

• Forms a leak-tight seal at a joint or fitting to stop drips and seepage
• Helps maintain proper fluid or refrigerant pressure where used
• Commonly replaced when cracked, flattened, or hardened
• Can eliminate intermittent leaks that occur under load or when the appliance cycles

• Turn off and unplug the appliance and shut off water or refrigerant supply before service
• Inspect mating surfaces and replace any damaged fittings to ensure a proper seal
• Lightly lubricate the O-ring with appliance-safe silicone grease; avoid petroleum-based products
• Do not stretch or nick the O-ring during installation; confirm correct seating before restoring power or supply

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This is a replacement bolt fastener that secures interior and exterior appliance components for stable operation and safe use. It restores proper fit where a worn or missing bolt causes looseness or rattling. What it does:

• Secures panels, brackets, or assemblies to prevent shifting and vibration
• Restores proper alignment for doors, drawers, or mounted components
• Helps stop rattling, squeaks, or visible gaps caused by a missing or damaged fastener
• Provides a durable connection when the original bolt is stripped, corroded, or lost

• One replacement bolt

• Use the correct size socket or wrench to avoid rounding the head
• Hand-start threads to prevent cross-threading; tighten until snug—do not overtighten
• Disconnect power and empty affected areas if working near electrical components or sharp edges
• Replace with the exact OEM bolt for best fit and function