Fcrg3052bs Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This ignitor orifice assembly sits under the cooktop and both routes gas to a surface burner and provides the spark to light it. Replace a damaged or clogged assembly to restore fast, reliable ignition at that burner.

• Feeds gas from the valve to the burner and houses the spark igniter electrode for ignition
• Common fix for a surface burner that won't light, has no or weak spark, or only lights with a match
• Also called an igniter/orifice holder assembly

• Disconnect power and shut off the gas supply before servicing.
• Raise or lift the cooktop per your model's service information; support it to avoid strain on gas lines.
• Note wire routing; set the electrode gap to the burner head per service specs and keep the lead away from heat/sharp edges.
• After reassembly, check all gas connections with an approved leak-detection solution and verify proper spark and flame.

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Outer Oven Door Panel is an OEM component specially designed for Frigidaire ranges. Constructed of durable steel, it forms the front facade of the oven cavity entrance. 

Prolonged heating cycles from baking subject panels to thermal stresses that cause warping and paint discoloration over time due to typical door element heating and cooling. Fatigue jeopardizes functionality.

Causes relate to the normal expansion and contraction cycles expected of an oven door exposed to repeated preheating. Impacts pose abrupt risks to the protective steel facing.  

Symptoms of a bad door panel involve:

• Unsightly stain pigment changes dimming the finish
• Noticeable bowing or tweaks in planar surfaces  
• Gaps appearing at seam borders from structural strain

Replacing with this OEM Frigidaire panel restores a smooth, attractive entrance for cooking tasks. Compatibility fits Kenmore, Electrolux, and Gibson brands ensuring steady performance with upgraded cosmetics.

Size: 8-32t x 0.500 inch. Color: Black.

The Glass is an OEM part for Frigidaire freestanding ranges. It provides a durable transparent barrier that allows for viewing of contents inside the oven. The tempered glass door is both impact-resistant and heat-resistant, built to withstand repetitive use.

Causes of bad oven door glass include cracks or chips developing from accidental impacts, warping or discoloration from overheating, or scratches that won't wipe clean. 

Symptoms of a bad glass oven door include:

• Inability to safely or securely close the oven door  
• Reduced visibility into the oven cavity
• Potential safety hazards from cracked or compromised glass

This OEM Frigidaire replacement restores the door's integrity and functionality. It is also compatible with Electrolux, Kelvinator, and some Kenmore electric range models. 

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

This door hinge is a direct-fit replacement part that supports and aligns an appliance door for smooth opening and secure closing. Replacing a worn hinge restores proper fit and prevents door sag, binding, or noisy operation. What it does:

• Provides the pivot point that lets the door open and close smoothly.
• Keeps the door aligned so seals meet and the door closes fully.
• Restores stable door movement and reduces sagging or rubbing.
• Helps stop binding, unusual noises, or doors that don't stay closed.

• Disconnect power to the appliance (and water supply if applicable) before starting work.
• Support the door while removing or installing the hinge to prevent damage or injury.
• Keep original screws and mounting hardware; new fasteners may be required if originals are worn.

The Burner Grate is an OEM part for Frigidaire gas ranges. It supports racks and pans directly over the range's gas burners during cooking. The burner grate must withstand constant exposure to high heats without warping or degradation.

Causes of a bad burner grate include wear from heavy use over multiple years, corrosion from spills or food particles left on the grate, or cracks and chips that compromise durability and function.  

Symptoms of a bad burner grate are:

• Uneven or inefficient heat transfer to pots and pans during cooking  
• Warping or distortion of grate bars impacting pan support
• Sharp edges or breakage causing potential safety hazards

This OEM replacement grate is also compatible with some Electrolux, Crosley, and Amana gas ranges.