Fef455wfba Parts

This is a metal wire rack designed to slide into the oven cavity on interior supports. It provides a flat, heat-resistant surface for holding cookware and baking sheets during cooking. Replace this rack if it is warped, rusted, has broken or bent wires, or no longer slides smoothly on the oven guides.

This oven thermostat senses and regulates oven temperature so food cooks evenly and the range reaches set temperatures. It replaces a failed temperature control to restore accurate heating and cycle behavior. What it does:

• Closes and opens the control circuit to maintain the oven at the selected temperature
• Can correct symptoms such as oven not reaching set temperature, overheating, or excessive cycling
• Works with the oven's control system and heating elements to stabilize bake and broil operations
• Mechanical design — avoid bending or damaging the sensing element/capillary

• One oven thermostat

• Disconnect power to the appliance before starting any service
• Handle the thermostat and sensing element carefully; do not kink or sharply bend the capillary
• Verify proper thermostat mounting and oven cavity seals for accurate temperature control

Secures cooktop surface elements to your range for stable contact and even heating. Replace if bent or worn to restore proper element positioning.

This is the rear panel that mounts on the back of a freestanding range, enclosing and protecting the internal wiring, insulation, and components behind the oven cavity. It helps maintain proper airflow and shields electrical connections from damage. Replace this panel if it is dented, rusted through, or missing, which can compromise insulation efficiency and expose internal components.

Range won't power on or burners not heating? This terminal block receptacle restores electrical connections. Moderate DIY repair, typically 30-45 minutes.

Nylon guide that supports the front of your range oven drawer as it slides in and out. Replace if cracked, broken, or worn causing drawer misalignment.

Mounting screw secures heating element to cooktop surface. Replace if stripped, rusted, or missing to ensure proper element installation and stability.

Decorative trim panel that covers the base of your range. Replace this toe plate if it's cracked, scratched, or missing to restore a finished look.

This hinge pin spacer helps position the refrigerator door hinge pin for proper door alignment and smooth operation. It replaces a worn or missing spacer to restore correct hinge spacing and reduce door binding. What it does:

• Holds the hinge pin at the correct height and offset for the upper or lower door hinge
• Helps prevent door sag, misalignment, and uneven sealing
• Reduces metal-on-metal contact and rubbing that can cause noise or wear
• Works at either the upper or lower hinge location as specified for your model

• One hinge pin spacer

• Disconnect power to the appliance or unplug the refrigerator before starting any repair
• Support the door while removing hinge hardware to prevent the door from falling
• Reuse existing hinge pin and hardware unless damaged; replace any worn fasteners

Seals the outer glass panel on your range oven door to prevent heat loss and improve efficiency. Replace if worn, cracked, or heat escapes. Verify fit.

Endcap for electric ranges. Covers and protects the end of a trim or component. Replace if cracked, broken, or missing to restore appearance.

This refrigerator/freezer door gasket creates an airtight seal around the door to help maintain proper temperature and reduce energy use. It replaces a worn or damaged seal to improve cooling and reduce frost buildup. What it does:

• Seals the cabinet to keep cold air in and warm air out
• Helps prevent excess frost and moisture inside the compartment
• Reduces compressor run-time caused by air leaks
• Restores proper door alignment and consistent cooling

• Disconnect power and remove food from affected compartment before starting
• Remove the old gasket and thoroughly clean and dry the gasket channel before installing
• Press the new gasket into the channel evenly, starting at a corner and working around the door
• Check the seal by closing the door; adjust or reseat as needed for a uniform contact

Range won't power on or loses electrical connection? This terminal block secures the power cord connection. Direct part replacement restores reliable operation.

Rubber or plastic bushing that cushions and supports the oven door. Replace if cracked, worn, missing, or causing door misalignment or rattling.