Ffbd2406 Parts

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This sump assembly is the dishwasher's lower-tub pump housing that circulates and drains wash water. Replacing a cracked or clogged sump restores proper drain and circulation, helping stop leaks and restore normal wash performance. What it does:

• Houses the pump and channels wash water for circulation and draining.
• Restores proper drainage when the dishwasher won't drain or holds water in the tub.
• Stops leaks that develop from cracked or damaged sump housings at the base.
• Reduces pump noise or grinding caused by debris, cracks, or a failing housing.

• Disconnect electrical power and water supply before beginning any service.
• Access the sump from the dishwasher's lower front (remove the lower rack and toe-kick/access panel as needed).
• Take care with wiring and hose clamps; transfer any motors, seals, or fittings only if required and follow manufacturer torque/placement.
• After installation, run a short cycle and inspect for proper drain/circulation and any leaks before reassembling trim.

This replacement switch assembly restores proper signaling between the dishwasher's mechanism and the control, so selected functions register and cycles can start and run consistently. A worn or failed switch can cause intermittent or no operation. What it does:

• Provides the on/off signal the control needs when the mechanism is actuated
• Can lead to a dishwasher that won't start or stops mid-cycle when failing
• May cause options or selections to be unresponsive or require extra pressure
• Heat damage or a broken actuator on the switch assembly can indicate failure

• 1 switch assembly

• Disconnect power to the dishwasher before servicing
• Access location varies by model; refer to your model's parts diagram/service information
• Photograph wiring and move connectors one at a time to the new assembly
• Verify secure connections and proper wire routing to prevent pinching during reassembly

This replacement screw secures appliance components so panels, brackets, and trim stay tight and properly aligned. Replace a missing, stripped, or corroded fastener to restore a solid fit and help stop vibration or rattling.

• Fastens components to the chassis or assembly for correct fit
• Helps maintain alignment and reduce movement and noise during operation
• Restores secure mounting when original hardware is missing, rusted, or stripped
• Typical symptoms: loose panel or handle, rattling noises, hardware backing out

• Disconnect power; if servicing a dishwasher, also shut off water
• Match the screw to the original location before installation
• Start threads by hand to avoid cross-threading, then tighten snugly without overtightening

This Main Wiring Harness is an OEM part for Frigidaire dishwashers. This harness transmits electrical signals to various components within the dishwasher.

Causes of a Bad Part: Wear and tear due to constant use, heat exposure, or moisture infiltration can cause the wiring harness to fray or short-circuit. Physical damage or manufacturing defects can also contribute to its malfunction.

Symptoms of a Bad Part:

• Inoperative dishwasher functions
• Electrical sparks or burning smell
• Visible damage or fraying on the wiring

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement dishwasher door forms the hinged front of the tub. Replacing a bent or damaged door restores proper alignment and latching so cycles can run correctly and the wash chamber remains properly contained.

• Creates the front barrier of the wash chamber and supports the latch/handle area
• Aligns with the door gasket to promote a proper seal
• Restores correct closing and latching so the cycle can start
• Common symptoms: difficulty closing, cycle won't start due to door not latching, visible dents/warping, poor seal along the gasket

• Disconnect power and turn off the water supply before servicing
• Support the door and carefully relieve hinge spring tension during removal
• Transfer any reusable components from the old door to the new one as needed
• Run a test cycle to ensure proper latching

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This console panel is the exterior fascia for the control area. It refreshes the appliance's appearance and provides proper support and alignment for the user interface components so the controls sit correctly and operate as intended.

• Forms the finished front of the control console in a black finish
• Supports and aligns the user interface/controls and related mounting hardware
• Helps shield internal controls from incidental contact at the front of the appliance
• Typical signs to replace: cracked or broken plastic, loose or missing tabs, misaligned controls, cosmetic wear or discoloration

• Disconnect power before servicing; wear cut-resistant gloves
• Photograph control layout and wire routing to aid reassembly
• Transfer existing screws, clips, handle trim, and user-interface parts to the new panel
• Ensure wiring isn't pinched and controls move freely before fully tightening fasteners

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

A small spring-style hose clamp that secures flexible tubing to fittings to help prevent leaks and hose separation. Replaces a worn or loose clamp to restore a tight seal on water and drain connections. What it does

• Compresses around a hose to hold it firmly on a barbed or smooth fitting
• Helps stop leaks and reduces chance of hose slip-off under pressure
• Commonly used on water, drain, and vent hoses where space is limited
• Simple, spring-action design keeps consistent tension as hoses expand/contract

• Disconnect power and shut off water supply before servicing appliance
• Use pliers to expand the clamp, slide into position, then release to seat it
• Inspect hose and fitting for damage; replace hose if cracked or brittle
• Do not overtighten or modify the clamp; replace with the exact style/size for a proper seal

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present

Replacement screw that secures trim, panels and internal components to restore proper fit and reduce rattling. Use when a fastener is missing, stripped, or corroded to help maintain stable, safe appliance operation. What it does:

• Secures panels, trim, brackets or other appliance parts to prevent looseness or movement.
• Replaces missing, worn, or damaged screws so components align and operate correctly.
• Helps reduce rattling, vibration noise, and gaps around doors or panels.
• Verify the exact size and thread before ordering to ensure proper fit.

• Disconnect power and water before starting any repair.
• Use the matching screw size and thread; do not force or overtighten.
• Start threads by hand to avoid cross-threading; use the correct screwdriver or bit.
• If threads or mounting holes are damaged, repair before reuse.

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit