Ffg3131wb Parts

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This solenoid-operated water inlet valve controls the flow of household water into the dishwasher during fill. A working valve ensures the tub fills to the proper level for effective cleaning and stops water when the cycle ends.

• Opens and closes as signaled by the control to admit water into the tub
• Regulates fill rate/level; seals to prevent unwanted filling between cycles
• Failure symptoms can include no fill, slow fill, overfilling, or leaks at the valve/inlet area
• May trigger fill-related error or unusually long fill times

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve line pressure slowly
• Note wire harness and tubing orientation; take a photo for reference
• Use approved thread sealant/tape if specified by the manufacturer; check for leaks after installation and run a fill test

This ignitor orifice assembly routes gas to the oven igniter so burners light reliably. It replaces a damaged or clogged orifice to restore consistent ignition and safe burner operation. What it does:

• Directs gas flow from the manifold to the igniter/pilot so the burner can light
• Helps restore proper ignition when the burner sparks but fails to light
• Replaces corroded, clogged, or damaged orifice hardware that can weaken flame
• Works with standard oven/range ignition systems that use a separate orifice assembly

• One ignitor orifice assembly

• Turn off gas supply and disconnect power before attempting service
• Basic hand tools required; avoid overtightening fittings to prevent damage
• Check for gas leaks with a non-corrosive leak detector after installation

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This wiring harness routes power and signals between the appliance's control and various electrical components, restoring reliable electrical connections and helping the appliance operate as designed. Use it when wiring is damaged, corroded, or intermittent. What it does:

• Delivers power and signal paths between control boards, switches, and motors
• Restores lost or intermittent electrical connections that can cause failure to start or run
• Replaces burned, frayed, or broken wires and damaged connector terminals
• Helps eliminate arcing, shorts, and communication errors caused by faulty wiring

• Always disconnect all power (unplug or shut off breaker) before starting repairs
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Inspect mating connectors and terminals for damage before installation; replace any damaged parts
• If connectors are tight or corroded, clean or replace them rather than forcing connections

This single replacement control knob restores safe, easy control of a range or oven when the original knob is missing, cracked, or worn. It provides a simple push-on replacement to make temperature and function selection straightforward again. What it does

• Replaces a damaged or missing control knob so you can set heat and cooking functions reliably
• Helps eliminate loose, cracked, or non-engaging knobs that make adjustments difficult
• Restores user interface for precise setting selection on ranges and ovens
• Works as a direct, single-knob swap to regain normal operation

• Disconnect power (or shut off gas) and allow appliances to cool before servicing
• Align the knob on the control shaft and push firmly until it seats; do not force if it resists
• If knob uses a retaining screw, tighten securely but avoid over-torquing

This genuine replacement screw secures appliance panels, brackets, or trim. Use it to replace a missing, stripped, or rusted fastener and restore a tight, rattle-free fit so components stay properly aligned during operation.

• Holds panels, brackets, or trim securely in place
• Replaces damaged, rusted, or missing hardware
• Helps resolve loose or rattling panels and misalignment
• Maintains proper assembly and stability during use

• Disconnect power; for gas appliances, also shut off the gas supply
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten to prevent stripping threads or damaging panels
• Repair or replace the mating clip/insert before installation

Replacement mounting bracket that secures internal appliance components to the cabinet or frame, restoring proper alignment and support. Helps reduce rattling and prevents loose or sagging parts for safer, quieter operation. What it does:

• Secures components or assemblies to the appliance frame to maintain proper alignment.
• Reduces movement and vibration that commonly cause rattling or intermittent contact.
• Helps prevent sagging or misalignment of attached parts that can affect operation.
• Simple, passive part — no electrical function.

• Disconnect power (and water, if applicable) before starting any repair.
• Use appropriate hand tools; inspect mounting holes and fasteners for damage or corrosion.
• Replace only the damaged bracket; do not overtighten fasteners to avoid cracking.

This ignitor orifice assembly routes and meters gas to the oven burner so the ignitor can light the appliance reliably. Replaces a worn or damaged orifice assembly to help restore consistent ignition and safe burner operation. What it does:

• Controls gas flow to the oven burner so the ignitor can light the flame
• Helps ensure a steady, consistent ignition and proper burner operation
• Commonly replaced when ignition is slow, inconsistent, or the burner won't stay lit
• Matches OEM design for fit and function in compatible gas ranges

• One ignitor orifice assembly

• Turn off gas supply and unplug the appliance before starting work
• Follow the appliance manufacturer's service manual for proper removal and installation
• Use appropriate tools and avoid overtightening fittings to prevent leaks