Ffha2611pfea Parts

This refrigerator housing is the molded support used to mount and protect its associated components inside the appliance. Replacing a damaged housing restores a secure fit and proper alignment so parts stay in place and function correctly.

• Provides structural support and mounting points for the related controls/components
• Helps route air and/or wiring as designed by the manufacturer
• Restores proper alignment to reduce rattles, rubbing, or interference
• Symptoms can include cracked plastic, broken tabs, loose or sagging assemblies, or components that won't stay secured

• Disconnect power before servicing; shut off water as needed if working near dispenser/ice components
• Transfer sensors, wiring, controls, and hardware from the original housing unless new parts are supplied
• Reuse original screws/clips; avoid overtightening to prevent cracking
• Verify harness connections and clearances before restoring power and water

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

This replacement retainer clip secures trim, panels or small components inside your appliance to restore proper fit and reduce rattling. A simple, low-cost part commonly used where plastic or metal pieces need a secure hold. What it does:

• Holds panels, trim pieces or small assemblies in place to prevent shifting and vibration.
• Helps stop rattling, loose trim or components that don't stay seated.
• Keeps wiring or hoses routed and restrained when used as a harness/route clip.
• Suitable when original clip is cracked, broken or missing.

• Disconnect power to the appliance before beginning any work.
• Remove surrounding trim or panels gently to access the clip location; a trim tool or small screwdriver may be helpful.
• Clip installs by pressing into the mating slot or hole until it snaps; pliers may assist for removal/replacement.
• Verify correct orientation and fit by comparing the new clip to the old one before final reassembly.

This refrigerator bracket is the OEM mounting piece that secures a specific internal assembly in place. Replacing a cracked or missing bracket restores a solid fit, proper alignment, and smooth, rattle-free operation of the attached component.

• Provides a rigid mounting point for the designated refrigerator component
• Maintains proper alignment to help the assembly operate correctly
• Helps reduce vibration and movement that can cause noise or wear
• Typical signs of failure: broken tabs, stripped holes, loose or misaligned parts

• Disconnect power; turn off water supply if working near ice/water components
• Access the area per your product's diagram; retain and reuse existing screws/fasteners
• Transfer any clips, spacers, or grommets from the old bracket to the new one
• The mounted component seats fully and operates before reassembling panels/shelves

Replacement water tube that carries water from the inlet valve to the dispenser and ice system, restoring water delivery and preventing leaks when the original tube is cracked, clogged, or disconnected. What it does:

• Routes water from the refrigerator inlet valve to the ice maker and/or water dispenser.
• Restores normal water flow when the existing tube is blocked, kinked, or leaking.
• Helps stop leaks and puddling caused by cracked or damaged tubing.
• Matches original routing and connections to maintain proper water delivery.

• Disconnect power and shut off the refrigerator water supply before starting work.
• Drain remaining water from the line and place a towel or tray to catch drips.
• Inspect connection fittings and any O-rings; replace seals if damaged to prevent leaks.
• After installation, restore water and power, then check all connections carefully for leaks.

This replacement water tank stores and supplies fresh water to the refrigerator's dispenser and ice maker, restoring proper water delivery and reducing leaks or slow/irregular filling. Designed to match the original fit and function. What it does:

• Holds the refrigerator's fresh water supply used by dispenser and ice maker
• Replaces a cracked, leaking, or otherwise damaged reservoir
• Helps restore normal dispenser flow and consistent ice production
• Prevents water pooling or internal leaks from a compromised tank

• Disconnect power and shut off the water supply before beginning work
• Remove interior panels and trim carefully to access and replace the tank
• Handle the tank gently to avoid damage to mounting tabs and fittings
• After installation, turn on water, check all connections, and inspect for leaks

This light socket securely holds the appliance bulb and provides the electrical connection to illuminate the compartment when the door is opened. Replacing a faulty socket restores interior lighting so you can easily see contents.

• Provides the electrical connection and physical mounting for the light bulb
• Common failure symptoms: light won't turn on, flickers, or only works when the bulb is jiggled
• Show signs of heat discoloration, loose terminals, or intermittent contact

• Unplug the appliance before service; power is off
• Allow the bulb and surrounding area to cool before handling
• Handle wiring carefully; transfer conductors to the new socket one at a time to maintain correct connections
• Do not exceed the bulb type/wattage specified on the appliance rating label

This retainer is a small mounting clip that secures internal components and trim to keep panels and assemblies aligned during normal use. It restores secure fitment and reduces movement or rattling from loose parts. What it does:

• Holds panels, trim, or small assemblies in place to prevent shifting and vibration
• Helps stop rattling or buzzing caused by loose internal components
• Keeps parts aligned so doors, drawers, or panels operate smoothly
• Replaces cracked, broken, or worn clips that no longer grip reliably

• Disconnect power to the appliance before inspecting or replacing parts
• Remove surrounding panels or trim as needed to access the retainer; keep screws/fasteners for reassembly
• Snap the clip into the mating slot or tab until it seats; replace any damaged mounting points
• Replace all adjacent clips for consistent fit

This is an authentic OEM freezer basket bumper sourced directly from the manufacturer for use on freezer baskets. Freezer basket bumpers are attached to the baskets to keep them from sliding around inside the freezer. If the bumper breaks, the basket will not stay in place, and the contents could shift or fall out. Freezer baskets create more storage room inside a freezer. These baskets are normally located on the bottom of the freezer, with freezer racks located above. Freezer baskets are ideal for storing smaller packages that might not stack well on the racks. Over time, normal wear and tear may cause the bumper to crack or break completely; if this happens, the bumper should be replaced. Remove the contents of the freezer basket. Remove the freezer basket from the freezer. Push the new bumper onto the freezer basket. Replace the contents of the basket and put it back into the freezer. This handle freezer basket is made of high-quality, white molded plastic. It is designed for use in freezers manufactured by Frigidaire, Kenmore, Gibson, and Electrolux.

This drawer roller allows your refrigerator's bin or crisper drawer to glide smoothly along its track. Replacing a worn or missing roller helps restore easy opening and closing and prevents drawers from sticking or binding.

• Supports the drawer as it slides on the rail/track
• Helps correct stiff, rough, or noisy drawer movement
• Can reduce uneven sliding or a drawer that pops off the track
• Common wear item when drawers are overloaded or used heavily

• Unplug the refrigerator before servicing
• Remove the affected drawer to access the roller
• Note roller orientation and reuse existing fasteners if applicable
• Test drawer travel after replacement to ensure smooth operation

This evap coil cover protects the evaporator and helps direct airflow for more consistent cooling. It replaces damaged or missing covers to reduce frost buildup, keep debris away from the coil, and help prevent interior leaks. What it does:

• Shields the evaporator coil from ice, debris and accidental contact to protect coil fins.
• Helps channel airflow across the coil for improved cooling performance.
• Can reduce frost accumulation and related moisture or dripping symptoms.
• When cracked or missing, you may notice increased frost, water in the cabinet, or reduced cooling.

• Always disconnect power to the appliance before servicing.
• Remove interior liners or access panels to reach the evaporator; handle coil fins and insulation carefully.
• Reinstall any mounting clips, grommets, or insulation exactly as removed to maintain fit and sealing.

This anti-twist pin secures mating parts to stop unwanted rotation and keeps linked components aligned for reliable operation. Replace a worn or broken pin to restore proper fit and reduce twisting, rubbing and noise. What it does:

• Keeps connected components from rotating or shifting, preserving alignment and part engagement.
• Helps prevent rubbing, scraping, or noisy operation caused by a loose or missing pin.
• Replaces a damaged or worn locating/retention pin that can allow assemblies to bind or move out of position.
• Simple mechanical replacement that restores intended part geometry and fit.

• Disconnect power to the appliance before servicing to avoid electrical or motion hazards.
• Remove any covers or panels as needed to access the pin; keep track of fasteners and orientation.
• Install the pin in the same orientation as the original; components move freely and are properly engaged before reassembly.

This support beam is a structural cabinet brace that stabilizes the refrigerator's interior frame and restores proper alignment of doors, drawers and shelves, helping reduce sagging, vibration and unusual noises. What it does:

• Reinforces the cabinet/frame so internal components stay square and aligned
• Helps prevent doors and drawers from sagging or binding
• Reduces rattling or vibration caused by a bent or missing brace
• Common symptom indicators: visible bend or gap, uneven door fit, or persistent noise from the cabinet area

• Disconnect power and remove food/contents from the affected area before starting any repair
• Basic hand tools typically required; follow the manufacturer's service manual for correct fastener torque and placement
• Handle carefully to avoid scratching the finish; inspect surrounding mounting points and replace damaged fasteners as needed

This rivet is a metal fastener used to permanently secure panels, brackets, or internal components in your appliance. Replacing a damaged or missing rivet restores a tight fit and helps prevent vibration, rattles, and looseness.

• Permanently joins thin metal parts where screws or nuts aren't used
• Maintains alignment and structural integrity of housings and frames
• Helpful when panels or components are loose, rattling, or won't stay secured
• Direct replacement for a worn, broken, corroded, or drilled-out factory rivet

• Disconnect power and shut off gas/water (as applicable) before servicing
• Support the part being fastened; drill out the old rivet head if needed
• A hand riveter/rivet tool may be required to set the new rivet
• Wear eye and hand protection during drilling/riveting

This replacement slide is a small guide piece that helps a movable component in your appliance travel smoothly and stay aligned, restoring easy, consistent operation when the original wears or breaks and causes sticking or rough movement.

• Guides a moving part along its track for smooth, stable travel
• Helps maintain alignment to reduce friction, binding, and uneven motion
• Worn slides can cause sticking, scraping, popping noises, or misalignment
• Visible wear, cracks, or deformation indicate the slide should be replaced

• Disconnect power and shut off gas/water supplies before servicing
• Note the original slide's orientation and mounting points for accurate reinstallation
• Reuse existing screws/clips if applicable; tighten securely without overtightening
• Cycle the component through its full travel to ensure smooth operation