Ffhf2322mfja Parts

This trim facade is the front decorative trim piece that finishes the appliance's control area and improves the cabinet appearance. It replaces cracked, scratched, or discolored trim to restore a clean, finished look. What it does:

• Covers and protects the front edge of the control panel or cabinet opening
• Restores a uniform, finished appearance when original trim is damaged or worn
• Helps keep dirt and moisture from reaching internal panel edges
• Fits to the appliance using existing clips or fasteners for a secure fit

• Disconnect power to the appliance before starting work
• Remove any surrounding trim or screws as needed to access clips or fasteners
• Align trim with existing mounting points and press or secure with original hardware
• If clips or screws are damaged, replace them before final installation

Refrigerator not cooling or running constantly? This compressor with inverter restores proper cooling. Advanced repair requiring refrigerant certification.

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

Protective cover that snaps over your freezer's door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.

Left-hand gray upper hinge cover snaps over the top door hinge to conceal hardware and restore a finished look. Replace when cracked, broken, or missing.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This electronic control board serves as the appliance's controller, managing cooling functions, sensor inputs, and status indicators. Replacing a faulty controller can restore stable temperatures and reliable operation.

• Regulates cooling based on temperature-sensor feedback to maintain the set point
• Switches major loads (such as compressor and fan) on and off as designed
• Interfaces with user controls and any status lights/alarms, when equipped
• Common failure symptoms: no cooling or overcooling, constant running, erratic cycling, or unresponsive/intermittent controls or indicators

• Disconnect power before servicing; electrical shock risk
• Handle the board by the edges and use ESD protection to prevent static damage
• Note/photograph all wire connectors before removal; transfer any mounting brackets or covers from the original part
• After reassembly, restore power and allow temperature to stabilize before final evaluation

Replacement sump that collects and channels condensation and defrost water into the refrigerator drain system, helping stop leaks and pooling under shelves or inside the cabinet. Restores proper drainage and reduces water buildup. What it does:

• Collects and routes defrost/condensation water into the fridge drain path and toward the evaporator pan or drain pump.
• Helps prevent water pooling inside the fresh-food compartment and puddles under the appliance.
• Can address symptoms like water under the refrigerator, slow or blocked drainage, or recurring puddles inside the cabinet.
• Sits in the drain channel and mates with the factory drain path to maintain a sealed flow.

• Disconnect power to the appliance before starting any repair.
• Remove interior shelves/drawers and the toe kick as needed to access the sump area.
• Inspect and clear the drain channel before installing; ensure the sump seats fully to avoid leaks.

Holds and seals the water filter cartridge in your refrigerator. Replace if the filter won't stay seated or if damaged. Confirm fit with your model number.

Replaces a worn or missing door stop cam riser that holds your refrigerator door at the correct height for proper closing. Restores smooth operation.

This beam-style crisper cover is the glass shelf that sits above the crisper drawer, providing a flat support surface and helping contain spills while keeping produce organized. It restores the shelf surface and proper crisper function. What it does:

• Replaces a broken or missing crisper cover to restore a stable shelf over the crisper drawer
• Helps contain spills and prevents items from falling into the crisper
• Supports produce and other refrigerated items above the drawer area
• Works with the refrigerator's crisper beam/track system to maintain proper clearance and operation

• One crisper cover (beam-style) as shown

• Always unplug the refrigerator or shut off power before servicing interior components
• Remove food and any items from the shelf area before installation
• Handle the glass carefully; lift straight up/out from the tracks or supports and slide the replacement into position
• If the cover uses plastic clips or rails, inspect and replace damaged hardware to ensure a secure fit

Secures and supports the freezer drawer in your refrigerator, keeping it aligned and stable. Replace this bracket if yours is broken, cracked, or worn.