Ffle2022mw Parts

This hinge secures the door to the cabinet and provides a smooth pivot. Replacing a bent or worn hinge restores proper alignment and reliable latching so the door opens easily and closes securely.

• Provides the pivot point for the door to open and close
• Supports door weight and keeps it aligned with the latch/strike
• Wear or damage can cause sagging, rubbing, or squeaking
• A misaligned door may not engage the door switch, preventing the cycle from starting

• Disconnect power before servicing; shut off gas supply
• Support the door before removing mounting screws to avoid strain or damage
• Note hinge orientation; transfer any spacers/shims and reuse existing hardware
• Align the hinge, snug screws, then tighten fully and test door operation

This pressure sensor monitors system pressure and sends pressure feedback to the control board so the appliance can manage cooling cycles accurately. Replacing a faulty sensor helps restore proper pressure feedback and reliable cooling performance. What it does:

• Monitors internal refrigeration pressure and provides sensor feedback to the control board.
• Helps the control board regulate compressor and cooling cycles based on pressure readings.
• A failing sensor can cause erratic cooling, extended run times, or error/fault codes.
• Works as a direct replacement sensor—the control system relies on accurate readings to operate normally.

• Disconnect power to the appliance before starting any service.
• Handle the sensor and wiring harness gently; avoid pulling on wires or connectors.
• Replace with the exact part number and secure all connections; improper wiring can cause faults.

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

This strike screw secures the door strike/catch to the appliance, keeping the latch aligned so the door closes firmly and any safety interlock engages. Replacing a missing, stripped, or corroded screw helps restore reliable, consistent door latching. What it does:

• Fastens the strike/catch to the door or cabinet
• Maintains proper alignment for positive latch engagement
• Helps address issues like door not latching, loose/rattling door, or intermittent door switch activation
• Replace if threads are stripped, the head is damaged, or the screw is missing

• 1 strike screw

• Disconnect power before servicing; allow hot surfaces to cool. For gas appliances, also shut off the gas supply.
• Support the door or strike and remove the damaged/missing fastener.
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening.
• Verify door alignment and latch/lock operation after installation.

Tub to pressure switch hose.

This replacement control knob lets you operate the corresponding control on your appliance with a solid, accurate feel. Restore clean appearance and dependable adjustment if the original knob is cracked, loose, missing, or stripped.

• Attaches to the control shaft to select and adjust settings
• Replaces knobs that are broken, cracked, or won't stay on the stem
• Helps correct slipping/spinning that prevents proper selection
• Restores pointer alignment and smooth, positive engagement

• Disconnect power (and shut off gas if applicable) before servicing
• Pull the old knob straight off the control shaft—do not pry against the panel
• Align the new knob with the shaft and press firmly until fully seated
• Test the control for proper engagement and pointer alignment before use

The Motor Control Board is an OEM part for Frigidaire washing machines. It functions as the central command center, directing all operations of the washer through electrical signals sent to components like the motor, clutch, and pump. The control board features precisely calibrated circuitry designed to execute cycle settings.

Causes can be short circuits, component failure from extended use, or water damage from leaks over time.

Symptoms of a bad motor control board include:

• The washer fails to start or complete cycles
• Strange electronic humming or buzzing noises
• Flashing lights and error codes displayed
• Inability to control cycle settings

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement screw secures appliance panels and components to restore proper fit and reduce movement. It's a simple, direct fix when small fasteners are missing, worn, or stripped and panels sit loose or rattle. What it does:

• Secures trim, panels, or internal components to keep parts aligned
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or damaged screws that prevent proper panel attachment
• Restores a safe, snug fit for covers and access panels

• Disconnect power or fuel supply before accessing the appliance for safety.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Tighten until snug; avoid over-tightening to prevent damage to threads or housing.
• Keep small parts away from children and pets during installation.

The Trunnion is an OEM part for Frigidaire washing machines. It allows the outer wash tub to rotate during agitation and the spin cycles. The trunnion is a heavy-duty, durable component designed to withstand the rigors of repeated cycles and turbulent wash motions.

Causes of a bad trunnion can be wear over extended use, damage from unbalanced loads that strain the pivot point, or fractures from impact or manual mishandling.

Symptoms of a bad trunnion include:

• Excessive vibration or shaking during operation
• Noisy or grinding sounds emanating from the tub area
• Difficulty starting or stopping tub motions
• The tub failing to rotate properly during cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small rubber mounting grommet that cushions and secures appliance components to reduce vibration and protect wiring or mounts from chafing. Replaces a worn or missing grommet to restore proper fit and quiet operation. What it does

• Cushions and isolates panels, brackets, or wiring to reduce noise and vibration.
• Protects cables and hoses from rubbing against metal edges.
• Helps keep components aligned by providing a snug, flexible mount.
• Common symptom: noise, rattling, chafing marks, or a loose fit where a grommet is missing or deteriorated.

• One rubber grommet as shown.

• High-level task; verify power is off and the appliance is disconnected before accessing the area.
• Inspect surrounding clips, screws, or wiring for damage and replace if needed.
• Push into the mounting hole until fully seated; ensure the mating component fits securely over the grommet.

This screw is a direct-replacement fastener used to secure appliance panels and components. It provides a simple, reliable fix when a missing or damaged screw lets parts sit loose or vibrate. What it does:

• Secures service panels, trim pieces, brackets, or small components
• Restores proper fit and alignment to reduce rattling or movement
• Replaces stripped, missing, or corroded screws to maintain safe assembly
• Works wherever the OEM screw specification is required for reliable fastening

• Use the correct driver bit and turn gently to avoid stripping the head
• Ensure mating threads are clean and aligned before tightening
• Tighten until snug; do not over-torque to prevent damage to threads or parts
• Disconnect power before working near electrical components or controls

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

Self leveling leg pad

Ceramic dryer heating element housing insulator.