Ffq5000 Parts

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

This control panel is the exterior front panel that houses the oven/range controls and provides a finished look while protecting the underlying electronics. It restores a secure mounting surface and normal control access. What it does:

• Provides the user interface area and mounting surface for control buttons, knobs, or touch controls
• Protects internal control electronics from spills, heat, and debris
• Restores a flush, finished appearance when the original panel is cracked, dented, or missing
• Resolves issues where buttons or switches sit unevenly or are difficult to operate due to damaged trim

• Disconnect power to the appliance before starting any repair to avoid electrical shock
• Remove adjacent trim and mounting screws to access and replace the panel; handle carefully to avoid scratching or bending
• Keep all original fasteners; replace only parts explicitly required
• If controls or electronic modules are mounted to the panel, verify attachment and wiring connections before restoring power

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This door seal creates a tight closure around the appliance door to help keep cold air in and warm air out, improving cooling performance and reducing energy use. Replace a worn seal to restore a proper door seal. What it does

• Forms a continuous gasket around the door edge to block air leaks.
• Helps prevent frost build-up and loss of cooling inside the compartment.
• Can reduce cycling and strain on the compressor when the seal is intact.
• Common symptom: noticeable cold-air leakage, frost near the door, or uneven cooling.

• High-level task; remove the old seal by pulling out the retainer and fit the new seal into the door channel.
• Warm the gasket slightly to help seat it evenly; avoid open flames or excessive heat.
• Inspect door frame and retainer for damage before installing the new seal.

This replacement tube routes defrost melt and condensation away from the freezer compartment to the drain pan, helping prevent leaks and ice buildup. Fits specific Frigidaire refrigerator models—check product fit for compatibility. What it does:

• Channels defrost water from the evaporator area to the drain system to prevent pooling
• Helps stop ice accumulation that can block drains and reduce cooling efficiency
• Restores proper water flow when original tube is cracked, split, or clogged
• Compatible direct-replacement when matched to the appliance model/PN

• Disconnect power before starting any repair to avoid electrical shock
• Use appropriate clamps or retainers from the appliance as originally installed; replace damaged clips if needed

This push button is the user-facing control button that replaces a worn, broken or missing oven/stove/range or appliance selector button, restoring tactile control and reliable user input. It fits into the front control panel and provides the mechanical interface for selections. What it does:

• Replaces a cracked, stuck or missing control button so selections register correctly
• Restores tactile feedback and proper engagement with the underlying switch or mechanism
• Helps stop intermittent control issues caused by damaged or loose buttons
• Useful when the button housing is chipped or cosmetically damaged

• Disconnect power to the appliance before attempting service to avoid shock or unintended operation
• Typically snaps into the front control panel; remove the old button by pulling straight out and press the new button into place
• Inspect the underlying switch for damage while replacing the button and replace that switch if necessary