Ffse5115pwo Parts

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

This replacement pulley guides the drive belt so the drum or tub turns smoothly and reliably. A worn pulley can squeal, shred belts, or stop the load from tumbling or spinning.

• Guides the drive belt and helps transfer motor power to the drum/tub
• A seized or damaged pulley can cause the drum/tub not to turn or to stall
• Inspect for cracks, wobble, or rough bearings during diagnosis

• Disconnect power before servicing; if working on a gas dryer, also shut off the gas supply. For washers, turn off water.
• Access the belt path; release belt tension and remove the old pulley.
• Install the new pulley and route the belt correctly; rotate by hand to confirm smooth tracking.
• Inspect and replace a worn drive belt or related belt-drive components while open.

This OEM fastener replaces a worn, stripped, or missing nut to securely hold components in place inside compatible laundry appliances. Restores proper clamping force to reduce vibration, rattling, and loosening during operation. What it does:

• Secures a mating bolt or stud to keep brackets, panels, or rotating parts firmly mounted
• Restores proper tension after the original nut is lost, corroded, or damaged
• Helps address symptoms like excessive vibration, rattling, or loose assemblies
• Maintains a tight connection in high-vibration environments when properly tightened

• 1 nut

• Disconnect power (and water to a washer) before servicing
• Support the component being fastened; hold the bolt head while loosening/tightening the nut
• Start threads by hand to avoid cross-threading; tighten to manufacturer guidance
• Replace any damaged bolts or hardware it mates with for a secure repair

This retainer is a small fastener that secures a component inside your appliance, keeping it correctly positioned during operation. Replacing a damaged or missing retainer helps eliminate looseness and noise while preventing wear from parts shifting.

• Holds a mating part or assembly firmly in place
• Restores proper fit when the original retainer is cracked, warped, or missing
• Common symptoms: loose or misaligned parts, rattling/vibration, rubbing noises
• Helps prevent premature wear from movement or chafing

• Disconnect power; shut off gas and water supplies if applicable
• Use your model's diagram to locate the retainer and match its orientation
• Transfer any reusable hardware and ensure the retainer is fully seated
• Reassemble and run a short test to check for proper operation

This electrical wire harness connects key components to deliver power and signal paths so your appliance controls and features operate reliably. It replaces a damaged or worn harness to restore proper electrical connectivity. What it does:

• Routes power and signal between control board, sensors, and accessories
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps resolve symptoms like lights, fans, or controls not powering on or working erratically
• Maintains proper connector fit and wiring color-coding for correct hookups

• One electrical wire harness

• Disconnect power before inspecting or replacing the harness to avoid shock
• Confirm connector orientation and secure all clips; route wiring away from heat and moving parts
• Inspect mating connectors for damage and replace if corroded or burned

This genuine-style refrigerator water filter cartridge reduces common contaminants to improve water and ice taste and clarity. Designed as a direct-replacement filter to restore filtered water flow and quality. What it does:

• Filters chlorine taste and odor and reduces visible sediment commonly found in household water
• Restores clean-tasting drinking water and clearer ice production
• Helps prevent particulate buildup in dispenser and icemaker water lines
• Fits inline into designed filter housing for simple swap-out replacement

• One replacement refrigerator water filter cartridge (1 pack)

• Turn off the refrigerator water supply or dispenser before removing the old filter
• Follow refrigerator manual for filter housing removal and secure seating of new cartridge
• Flush several gallons of water through the dispenser after installation to clear air and carbon fines
• Dispose of used filter per local regulations;

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

This replacement cushion is a small rubber bumper that protects components and reduces vibration and noise where panels, doors, or assemblies meet. It helps keep parts aligned and prevents metal-on-metal contact. What it does:

• Absorbs shock and reduces vibration to minimize rattling or movement
• Protects surfaces from wear and prevents scraping or chafing
• Helps maintain proper spacing or alignment of panels or assemblies
• Works wherever a soft bumper or spacer is required

• Disconnect power to the appliance before servicing.
• Remove any covers or panels to access the mounting area.
• Press or seat the cushion into the locator/receptacle; replace retainers if present.

This door lock latch secures the appliance door during operation to help maintain proper function and prevent accidental opening. It replaces a worn or broken latch so the door stays closed and the cycle runs correctly. What it does:

• Secures the door shut so the appliance can run and maintain proper internal conditions
• Prevents the door from opening unexpectedly during cycles
• Stops leaks and heat/air loss caused by a faulty or loose latch
• Reduces noise and vibration caused by a misaligned or damaged lock

• Disconnect power to the appliance before attempting any repair
• Typical install requires removing the door inner panel or access cover; keep screws and fasteners organized
• Inspect the striker and surrounding trim for damage; replace if worn to ensure proper engagement

One per package.

The Steam Hose Kit is an OEM part for Frigidaire dryers. It provides the necessary conduit for steam from the water source to the dryer. The kit includes: 
5’ Rubber Fill Hose with Gooseneck
1’ Rubber Fill Hose (Female/Female)
All Male Y Connector

Causes of a bad steam hose can range from normal wear and tear to improper installation or physical damage from external sources.  

Symptoms of a bad Steam Hose Kit include:

• Leaks or drips from the hose connections.
• Reduced steam output, affecting the dryer's ability to effectively remove wrinkles or sanitize clothes.
• Noticeable wear or damage to the hose, such as cracks or splits.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.