Ffsh2611pfea Parts

Light stays on or won't turn on when you open the fridge door? This door-activated switch controls interior lighting. Simple DIY fix for most models.

Interior light stays on or won't turn on? This door-activated light switch controls your refrigerator lighting. Simple repair restores proper operation.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This replacement extension support restores proper alignment and secure mounting for the appliance component it attaches to, helping stop misalignment, rubbing, or loose parts and letting the appliance operate smoothly. What it does:

• Replaces a worn, broken or missing extension support used to secure or extend a nearby panel, drawer, or assembly.
• Helps stop rattling, uneven movement, or binding caused by a damaged support piece.
• Restores proper spacing and mounting so associated parts track and close correctly.
• Works as a direct-fit replacement when the original extension is damaged or missing.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle edges carefully; use basic hand tools and keep original fasteners if reusing them.
• If mounting hardware is missing or damaged, source matching screws/clips separately.

Control rod spring for refrigerator ice maker shutoff arm. Restores proper tension to control ice production cycles. Replace if spring is missing, broken, or worn.

OEM mounting bracket that secures the hinge and pin assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Fix rattling or misaligned fridge components with this anti-twist pin. Secures mating parts to prevent unwanted rotation and noise. Simple DIY fix.

Fix water pooling under crisper drawers or weak dispenser flow by replacing a cracked refrigerator water tank. Stores and chills water for dispensing.

The Motor Blower is an OEM part for Frigidaire refrigerator. It circulates cool air throughout the interiors to achieve and maintain the proper temperatures for food safety.

Causes of a bad motor blower can involve a worn or damaged motor bearing from years of continuous operation, or defective internal wiring causing electrical issues over many power cycles. Improper cleaning introducing moisture can also produce disturbances.

Symptoms of a bad motor blower include:

• Fluctuating or warmer than normal interior temps
• Frost or ice buildup from inadequate air flow
• Noisy vibrations or abnormal sounds from within
• Inability to precisely regulate temperature settings

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

This kickplate grille mounts across the bottom front of your refrigerator, covering the lower opening. Replace if cracked, broken, or missing.

Black plastic cover that snaps over the top door hinge on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

Refrigerator spacer maintains proper clearance and alignment between internal parts. Replace if worn, missing, or causing parts to rub or bind together.

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power