Ffsh2611pfea Parts

One per package.

This board-switch is an electronic control component that operates user-selected functions and sends signals to the appliance's control system. Replacing a faulty switch restores reliable input response and control of affected cycles or settings. What it does:

• Acts as the user-input switch assembly that tells the control board which functions or cycles to start
• Commonly linked to unresponsive buttons, no-start conditions, or intermittent control behavior
• Helps restore accurate command signaling when worn or damaged contacts fail to register presses
• Works as part of the appliance's front control/interface; does not include main control board unless specified

• One board-switch assembly as shown

• Disconnect power to the appliance before attempting any service to avoid shock or injury
• Handle the board and connector pins carefully; avoid touching contacts or static-sensitive components
• Minor disassembly of the console or control panel is typically required; keep fasteners and hardware organized

The Steam Hose Kit is an OEM part for Frigidaire dryers. It provides the necessary conduit for steam from the water source to the dryer. The kit includes: 
5’ Rubber Fill Hose with Gooseneck
1’ Rubber Fill Hose (Female/Female)
All Male Y Connector

Causes of a bad steam hose can range from normal wear and tear to improper installation or physical damage from external sources.  

Symptoms of a bad Steam Hose Kit include:

• Leaks or drips from the hose connections.
• Reduced steam output, affecting the dryer's ability to effectively remove wrinkles or sanitize clothes.
• Noticeable wear or damage to the hose, such as cracks or splits.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This wiring harness connects the appliance's control and power circuits so switches, controls and components receive reliable electrical signals. Replacing a damaged harness restores proper electrical routing and helps prevent intermittent operation or shorts. What it does:

• Transfers power and control signals between the control board, switches and components
• Replaces worn, cracked or damaged wiring that can cause intermittent function or failure
• Addresses symptoms like unresponsive controls, intermittent operation, blown fuses or visible wire damage
• Helps prevent arcing or short circuits from frayed or melted conductors

• Disconnect power before beginning work to avoid shock or damage
• Inspect connectors and routing; secure harness away from heat or moving parts
• Replace only if the part matches the original; compare connector count and routing

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces

This electrical wiring harness routes power and signals between components to restore reliable electrical connections. It replaces a damaged or worn harness to correct intermittent power, nonresponsive controls, or component failures. What it does:

• Carries electrical power and control signals between appliance modules and components
• Restores lost or intermittent electrical continuity caused by frayed wires or broken connectors
• Helps resolve symptoms like lights or components not powering on, sporadic operation, or control failures
• Maintains factory routing and connector fit for proper electrical performance

• Disconnect power before attempting any repair to avoid shock or damage
• Compare connectors and wire colors to the old harness to ensure correct replacement
• Use proper strain relief and routing to prevent chafing or pinching of wires

Sealer for refrigerant line insulation.

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This replacement door seal creates a tight perimeter seal to help keep conditioned air inside and reduce moisture or frost buildup. Fits factory specifications to restore proper sealing and improve efficiency. What it does

• Forms an airtight barrier around the door to limit air exchange and energy loss
• Helps prevent frost, condensation, and water pooling inside or under the appliance
• Reduces strain on the compressor by maintaining correct internal temperature
• Common symptom fix for visible gaps, torn or flattened gasket, or excessive frost buildup

• Seal as shown

• Disconnect power or unplug the appliance before starting any service
• Clean the door frame thoroughly before installing to ensure a good seal
• Work the gasket into the channel evenly; avoid overstretching or twisting
• If clips or retainer strips are present, follow OEM guidance for proper seating

Left hand side. For the right hand side order 241674402

This defrost drain pan collects water from the refrigerator's automatic defrost cycle and channels it safely to the evaporator area for evaporation, helping prevent leaks and water pooling beneath the appliance. What it does:

• Collects and channels defrost water away from the freezer/refrigerator cabinet
• Prevents water from pooling under the unit, which can cause floor damage or odor
• Helps proper evaporation of defrosted water at the compressor/evaporator location
• Reduces risk of ice build-up from standing water in the cabinet

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove lower access panels or kickplate to reach and replace the pan
• Inspect and clear the drain tube and heater while replacing the pan for best results
• Handle gently to avoid bending or cracking the pan

This small replacement sleeve protects and guides a moving component in the appliance to reduce wear and ensure smoother operation. It helps maintain correct alignment where parts slide or rotate, preventing metal-on-metal contact. What it does:

• Acts as a protective liner or guide for a rotating or sliding shaft or pin
• Reduces wear and friction between mating parts
• Helps stop scraping, squeaking, or uneven movement around the fitted area
• Supports proper part alignment for reliable operation

• One replacement sleeve as shown

• Replace only with the exact part number to ensure correct fit
• Inspect mating shaft/pin for wear and clean before installing the sleeve
• Apply light lubricant only if specified by the manufacturer; avoid over-lubrication
• Disconnect power and follow all safety guidelines before servicing the appliance

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

A single replacement screw used to fasten appliance panels and components, restoring secure fit and reducing vibration or noise. Simple, low-cost part for repairs that need a missing or stripped fastener. What it does:

• Secures panels, trim, or small component housings to the appliance frame
• Helps stop rattling, vibration, and misalignment caused by loose or missing screws
• Keeps internal components properly seated to maintain normal operation
• Used wherever the OEM specifies this exact fastener

• One replacement screw

• Disconnect power before servicing the appliance to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand first, then tighten snugly—do not overtighten
• Keep small parts away from children and pets