Fft1814q Parts

This door trim finishes the top edge of the appliance door, restoring a clean, finished appearance and covering the hinge/screw area. It helps maintain the door's look and protects internal edges from wear. What it does:

• Covers and protects the top edge and hinge/screw area of the door
• Restores a finished, factory appearance after damage or wear
• Prevents exposure of screws or trim gaps that collect dirt
• Helps keep the door edges aligned visually

• Remove power and open the door to access fasteners before replacing trim.
• Typical install uses screws or snap-fit tabs; keep original hardware unless replacement specified.
• Handle trim carefully to avoid scratching the finish during installation.
• Address hinge or door alignment issues separately; this trim covers cosmetic/edge areas only.

Air conditioner not cooling or won't start? This compressor replacement part restores cooling performance. Professional installation recommended.

Fix your air conditioner that won't cool or runs constantly with this condenser. Essential sealed system component for restoring proper cooling performance.

Replace a malfunctioning control panel when buttons stop responding or the display fails. Restores temperature and mode selection on room air conditioners.

This evaporator coil circulates refrigerant inside the freezer compartment to absorb heat and enable the cooling cycle. Replacing a damaged or corroded coil restores proper cold distribution and helps the appliance reach normal temperatures. What it does:

• Absorbs heat from the freezer compartment as part of the refrigeration cycle
• Allows refrigerant to evaporate and carry heat away from the cabinet
• Commonly replaced for frost buildup, poor cooling, or visible coil damage
• Works with the evaporator fan and defrost system to maintain even temperatures

• One evaporator coil as shown

• Requires access to the freezer back panel; follow for step-by-step removal
• Disconnect power before servicing to prevent shock or compressor damage
• Handle refrigerant lines carefully; if refrigerant must be opened, recover/recharge system
• Inspect surrounding components (evaporator fan, defrost heater/thermostat) while replacing for best results

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This block is a small mounting spacer used to secure and align components inside the appliance, helping maintain proper fit and operation. It replaces worn or broken mounting blocks to restore stable support and alignment. What it does:

• Provides a stable mounting surface or spacer between cabinet components
• Holds panels or assemblies in correct position to prevent rubbing or misalignment
• Helps reduce vibration or shifting of the connected parts during operation
• Commonly replaced when cracked, broken, or missing

• One mounting block

• High-level replacement; may require removing panels or trim to access mounting location
• Use appropriate hand tools and keep fasteners organized for reassembly
• Disconnect power before servicing any electrical components

This small retainer clip secures trim, panels, or components in place to prevent rattling and keep parts aligned. It's a simple replacement that restores proper fit and reduces vibration or loose panels. What it does:

• Holds appliance trim or panel pieces in position to prevent movement and noise
• Helps keep wiring or small components routed and secured away from moving parts
• Stops gaps or misalignment that can cause rubbing or vibration sounds
• Restores the intended fit where a worn or broken clip allows play

• Disconnect power to the appliance before starting any repair
• Access the clip location by removing the applicable trim or panel per your model's service instructions
• Use common hand tools; replace broken clips with the identical style to ensure proper fit
• Replace all matching clips for consistent fit

If your air conditioner won't start or runs intermittently, the capacitor may have failed. This part provides the voltage boost needed for startup.

If your air conditioner won't start or runs intermittently, a failing run capacitor is often the cause. This part helps the motor start reliably.

Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.