Ffue2022awg Parts

The Socket is an OEM part for Frigidaire refrigerators. It is responsible for holding and connecting the light bulb in the refrigerator, allowing for proper lighting inside the appliance.

A bad light socket can be caused by electrical issues, physical damage, or wear and tear over time. Signs of a faulty light socket include a non-functional light bulb, flickering or dim lighting, or a loose connection.

Symptoms of a bad light socket can include:

• The refrigerator light not turning on 
• Intermittent flickering or dimming of the light
• Difficulty in installing or removing the light bulb
• Visible damage on the socket

Replace your malfunctioning light socket with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This inverter is the compressor drive module that controls variable-speed operation to help your refrigerator cool efficiently and quietly. It replaces a failed drive unit so the compressor can respond to temperature controls. What it does

• Converts incoming power and controls compressor motor speed for proper cooling
• Restores variable-speed compressor operation when the drive has failed
• Resolves symptoms like reduced or no cooling, long run cycles, or inverter-related fault codes
• Works with the fridge's control system to regulate compressor performance

• One inverter (compressor drive) module

• Disconnect power to the appliance before starting; verify the unit is completely de-energized
• Handle the module carefully and avoid contact with exposed circuitry or connectors
• Match connector pins and mounting points; secure all electrical connections

This precision bearing supports a rotating component inside your appliance, reducing friction for smooth, reliable operation. Replacing a worn bearing can eliminate noise and restore proper movement in the affected assembly.

• Provides low-friction support for a rotating shaft or component
• Helps maintain alignment for smooth, quiet operation
• Common symptoms include squealing/grinding noises, wobble/play, or binding/seized rotation
• Excess drag can cause overheating or motor overload

• Disconnect power and shut off gas/water supplies as applicable before service
• Match orientation to the original and your model's diagram for placement
• Clean the shaft/bore and inspect mating parts; replace worn components; apply OEM-approved lubricant only if specified
• If press-fit is required, use proper drivers/press tools; do not hammer directly on the bearing

This replacement access cover restores the appliance's finished appearance while protecting internal components and controls from dust and debris. It helps keep wiring and small parts secure so the unit operates safely. What it does:

• Protects control assemblies, wiring and internal components from dust, spills and accidental contact
• Restores a secure, finished fit when the original cover is cracked, broken or missing
• Helps prevent loose parts from shifting during use and reduces risk of debris-related issues
• Visible damage, a loose or rattling cover, or gaps around the control area are common signs this part is needed

• One replacement access cover

• Disconnect power (unplug or switch off circuit) before starting any work
• Remove necessary trim or panels to access mounting screws; keep fasteners for reassembly
• Handle plastic clips and tabs gently to avoid breakage; use proper tools (screwdriver, trim tool)

This replacement cover is an access panel that protects internal components and keeps the appliance looking finished. It provides a secure barrier to help prevent debris from entering and allows service access when maintenance is needed. What it does

• Covers and protects internal parts from dust, dirt and incidental contact
• Helps reduce airflow of loose debris into the component area
• Provides a finished exterior appearance after repair or service
• Allows access to controls or components when removed
• Fits where the original factory cover was installed

• One replacement cover

• Disconnect power (and gas if applicable) before starting any repair
• Remove fasteners holding the old cover; keep hardware
• Align cover and reinstall screws until snug; do not overtighten
• Use caution: edges may be sharp and panels may be thin

This bottom door hinge is a direct replacement part that supports and guides the appliance door for proper alignment and smooth opening. Restores secure door mounting and helps maintain an even seal. What it does:

• Supports the bottom of the door and bears door weight
• Keeps the door aligned to close evenly and seal properly
• Prevents door sagging and uneven gaps that can affect cooling
• Reduces rubbing, scraping, or noisy operation from a loose hinge

• Disconnect power to the appliance and remove stored items from the door before starting
• Support the door while removing and installing the hinge to prevent injury or damage
• Use basic hand tools; follow torque recommendations from the manufacturer and avoid overtightening

This wiring harness routes power and signals between appliance components to restore reliable electrical connections and proper control operation. It replaces a worn or damaged connector assembly to help stop intermittent power or control failures. What it does

• Provides secure electrical connections between control, switches, and components
• Restores continuity when original wires or terminals are damaged or corroded
• Stops intermittent operation, control communication errors, or no-power symptoms
• Helps eliminate arcing or poor contact that can cause heat or burning smells

• One wiring harness assembly

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Confirm wire routing and connector orientation before disconnecting; photograph for reference
• Avoid pinching or stressing wires; secure harness with existing clips or ties

This replacement screw fastens appliance components so panels, brackets, and covers stay securely in place. Replace a missing, stripped, or damaged screw to restore a tight fit and help prevent vibration or noise. What it does:

• Secures panels, brackets, trim, or covers as designed for your model
• Replaces missing, rusted, or stripped hardware
• Helps correct loose or misaligned components
• Reduces vibration and rattling from loose fasteners

• Includes: 1 screw

• Disconnect power before servicing
• Wear gloves and eye protection
• Use the correct driver to avoid stripping the screw head
• Tighten snugly without overtightening; refer to your model's parts diagram for exact location

This sealed compressor kit replaces a failed refrigeration compressor to restore cooling performance in compatible refrigerators. Designed as a direct-replacement assembly, it provides the core refrigeration compression needed for the appliance to circulate refrigerant. What it does:

• Compresses refrigerant so the cooling cycle can operate and the refrigerator can maintain set temperatures
• Stops or reduces cooling when a compressor fails, hums, or does not start
• Addresses symptoms such as no cooling, warm compartments, or excessive compressor noise when confirmed faulty
• Works as the primary drive for refrigerant flow in the sealed refrigerant circuit

• Appliance must be disconnected from power before starting any repairs
• Proper evacuation, recovery and recharge of the refrigerant circuit is required per regulations and OEM instructions

This evaporator coil assembly circulates refrigerant inside the freezer compartment to absorb heat and enable proper cooling. Replacing a faulty coil restores cold temperatures and helps the system run efficiently. What it does:

• Evaporates refrigerant to remove heat from the freezer compartment
• Enables consistent cold airflow for proper food preservation
• Prevents excessive frost buildup when functioning correctly
• Helps reduce long run cycles caused by poor evaporator performance

• 1 evaporator coil assembly

• Disconnect power before starting work and follow basic electrical safety
• Inspect and replace damaged gaskets, insulation, or defrost components as needed for reliable operation
• Test system for leaks and proper cooling after installation

This evaporator fan assembly circulates cold air across the evaporator coil to maintain even refrigerator temperatures and proper cooling performance. Replaces a failed or noisy fan to restore airflow and reduce frost buildup. What it does:

• Spins to move cold air from the evaporator into the fridge and freezer compartments
• Helps maintain consistent internal temperatures for food preservation
• Worn bearings or a damaged blade can cause noise, rattling, or reduced airflow
• Restores airflow when a broken or seized fan prevents proper cooling

• One complete evaporator fan assembly (motor with blade and mounting as shown)

• Disconnect power before servicing to avoid electrical shock
• Access typically requires opening the evaporator cover—handle evaporator fins and wiring carefully
• Verify correct orientation and secure mounting to prevent noise and motor strain
• Allow the evaporator to thaw and dry before reinstalling

This filter-drier removes moisture and contaminants from a refrigerator's sealed refrigerant circuit to help protect the compressor and improve cooling reliability. It's a service replacement for sealed-system repairs. What it does:

• Traps moisture and acid from refrigerant to reduce corrosion and oil breakdown.
• Captures particulate debris that can clog expansion devices and reduce cooling.
• Helps restore proper refrigerant flow after a compressor or tubing repair.
• Common symptom: system not cooling efficiently or refrigerant circuit contaminated after failures.

• One filter-drier (quantity: 1)

• Intended for certified HVAC/refrigeration technicians only; sealed-system service requires proper tools and refrigerant handling.
• Replace only when the system is opened for repair (compressor, tubing, or evaporator replacement).
• Must be brazed into the liquid line, evacuated, and charged per manufacturer refrigerant and service specs.
• Dispose of and handle used refrigerant and components according to local regulations.

The Fan Mount is an OEM part for Frigidaire refrigerators. It is responsible for holding the evaporator fan in place within the refrigerator's freezer compartment.

A bad fan mount can be caused by regular wear and tear, physical damage, or improper installation. Signs of a faulty fan mount include excessive noise coming from the freezer, reduced cooling performance, or the fan not spinning properly.

Symptoms of a bad fan mount can include:

• Unusual noises coming from the freezer
• Insufficient cooling or uneven temperature
• The evaporator fan not spinning
• Excessive frost or ice buildup in the freezer

Replace your damaged or worn-out fan mount with this genuine OEM part to ensure proper airflow in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This cover protects the appliance's control board and wiring, keeping them secure from spills, dust, and physical damage so the controls work reliably and are easier to service. What it does:

• Shields the control board and associated wiring from moisture, dust, and accidental contact
• Helps prevent shorts and component damage that can cause control or electrical faults
• Keeps wiring and connectors routed and secured to reduce vibration-related issues
• Restores a finished appearance and proper airflow around control components

• One cover as shown

• Disconnect power before servicing to avoid electric shock
• Remove any mounting screws or clips holding the old cover, then lift off and fit the replacement in the same orientation
• Reinstall screws or clips securely but avoid overtightening plastic fasteners

This condenser coil assembly removes heat from the refrigerant so the refrigerator can cool properly. It's a direct-fit replacement that restores the cooling loop's ability to shed heat and run more efficiently. What it does

• Exchanges heat from the refrigerant to the surrounding air so the cooling cycle can continue
• Helps the compressor run within normal temperature range
• Commonly replaced when the refrigerator is warm inside or the unit runs continuously
• Needed if the condenser is bent, clogged with debris, or leaking

• One condenser

• Disconnect power to the appliance before starting any repair
• Handle with care — coil fins and tubing can be sharp and easily damaged
• Reinstalling may require removal of back or lower access panels; keep fasteners organized
• Sealed-system work (cutting or brazing refrigerant lines) requires certified HVAC service — do not attempt if refrigerant lines must be opened