Ffus2613lso Parts

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This genuine replacement clip secures appliance components to keep panels and small parts aligned and stable, restoring fit and function. It's a small, durable fastener used where a simple snap or hold is required. What it does

• Holds trim, panels, or small components in place to prevent rattling or misalignment
• Restores secure fit where a damaged or missing clip causes loose parts
• Helps stop vibration noise caused by unsecured pieces
• Small, direct-fit part—replaces a single broken or lost clip

• Disconnect power to the appliance before starting any repair.
• Access may require removing trim or panels; keep track of fasteners.
• Press or snap the clip into place; do not force beyond fit—if it won't seat, recheck alignment.
• Wear gloves and eye protection to avoid cuts from sharp edges.

Color: Black

This lower hinge secures and pivots a refrigerator door, restoring proper alignment and smooth opening. It helps stop door sag, uneven sealing, and rubbing that can cause cold loss or noisy operation. What it does:

• Provides a durable pivot point for the refrigerator door to open and close smoothly
• Restores correct door alignment to improve the door seal and cooling performance
• Stops door sag, rubbing against the cabinet, and uneven gaps that can lead to air leaks
• Helps reduce noise from a misaligned or worn hinge

• Support or remove the door before replacing the hinge to avoid injury or damage
• Keep fasteners and any hinge shims or bushings; reuse only if in good condition or replace with OEM parts
• Tighten mounting screws securely and check door alignment; minor shimming may be required

This black door stop replaces the small bumper that limits a refrigerator/freezer door's travel, protecting the cabinet and hinge from damage. It restores proper door alignment and quiets contact when the door closes. What it does:

• Acts as a physical stop to prevent the door from swinging too far and hitting the cabinet
• Cushions door closure to reduce noise and wear on the hinge
• Helps maintain correct door alignment for a tight seal
• Common symptom: door scraping, slamming, or rubbing against cabinet edge

• Basic hand tools may be required; keep fasteners and mounting surfaces clean
• Turn off or unplug the appliance before performing any repairs that require moving the door
• Handle hardware carefully to avoid damaging surrounding trim or seals

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

A single replacement screw used to fasten appliance panels and components securely. This genuine-style fastener restores proper fit and helps eliminate rattles or loose parts after service or repairs. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Restores tight, stable mounting to stop rattling or vibration
• Replaces missing or stripped hardware so parts align correctly
• Works where the original appliance screw was used

• Use matching driver and apply moderate torque to avoid stripping the head or threads
• Disconnect power or unplug the appliance when accessing internal areas
• If screw threads are damaged, replace with an identical part rather than forcing