Ffvu17fqwa Parts

Restore proper auto-defrost performance in your refrigerator. This defrost heater assembly melts frost off the evaporator during defrost cycles, and the included thermostat helps end the cycle at the correct temperature to prevent over-defrosting.

• Heats the evaporator to clear built-up frost and maintain airflow
• Thermostat monitors coil temperature to terminate defrost at the right time
• Common failure signs: heavy frost/ice on the evaporator, poor cooling, warm fridge but cold freezer, or frequent icing after defrost
• Helps reduce noisy fan icing and improves temperature stability

• Disconnect power before service; components get hot during and after use
• Access is typically from the freezer section behind the evaporator cover
• Note wire routing and clip locations before removal; transfer thermostat to the same position if applicable
• After installation, verify heater and thermostat connections are secure and unobstructed

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement handle restores a secure, comfortable grip so you can open and close your appliance door or drawer with confidence. Replacing a cracked or loose handle improves usability and appearance without affecting the door's alignment.

• Provides the handhold used to open and close the appliance
• Restores operation when the original handle is cracked, broken, loose, or missing
• Helps prevent damage from pulling on trim, frames, or the latch
• Refreshes the look when the old handle is scuffed or discolored

• Unplug or disconnect power before servicing
• Support the door/drawer while removing and installing the handle
• Remove interior/backside mounting screws; transfer original screws, spacers, or caps if required
• Align and tighten screws evenly; do not overtighten

This wire oven rack provides a sturdy platform for cookware and bakeware, restoring proper support and airflow inside the oven for even cooking. It fits in compatible Frigidaire/Whirlpool-style ranges and drop-in ovens. What it does:

• Supports pans, baking sheets and cookware securely during baking or roasting
• Helps maintain proper air circulation for consistent oven temperatures
• Replaces bent, warped or missing racks that cause unstable cookware
• Restores rack position options for broiling, baking and roasting

• One wire oven rack

• Slide rack into oven grooves until it seats; no tools required for most installs
• Allow oven to cool completely before installing or removing the rack
• Handle with care—edges may be sharp and the rack can be heavy when loaded
• Clean with nonabrasive cleaners; follow oven manufacturer cleaning recommendations

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed

This hinge cover protects and finishes the appliance's door hinge, restoring a clean appearance and helping keep the hinge area clear of dirt and debris. A simple cosmetic and protective replacement. What it does

• Covers and shields the door hinge to protect it from dust, grease and debris.
• Restores the appliance's finished appearance when the original cover is cracked, broken, or missing.
• Helps reduce the chance of exposed sharp edges from a damaged hinge area.
• A damaged or missing cover can contribute to visible hinge hardware and may make the door look misaligned.

• Support the door before removing any hinge hardware to prevent the door from shifting or falling.
• Handle edges carefully and wear gloves to avoid cuts from metal parts.
• Reinstall original mounting screws or clips; do not overtighten plastic components.

This door stop controls the door's swing, preventing it from opening past its designed angle and protecting the hinge and cabinet. Replace a cracked or missing stop to restore controlled door movement and help maintain proper alignment and sealing.

• Limits door opening angle to prevent overextension
• Helps protect hinges and prevent cabinet/wall impact
• Supports consistent door alignment and gasket contact
• Typical signs: door swings too far, visible broken/missing stop, scuffing near hinge area

• Disconnect power and support or unload the door to reduce weight before servicing
• Support the door; remove hinge cover/hardware as required by your model
• Note the original stop's orientation; transfer and secure with existing hardware
• Adjust hinges if needed

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This trivet is the cast metal support that sits over a cooktop burner to hold cookware steady and protect the burner assembly. It restores a level cooking surface and helps maintain safe, even contact between pots and the burner. What it does:

• Provides a stable platform for pots and pans on a cooktop burner
• Keeps cookware off the burner head to prevent direct damage
• Helps maintain correct clearance so flames and heat are directed properly
• Replaces cracked, warped or missing trivets that cause wobbling or uneven cooking

• Allow the cooktop to cool completely before handling the trivet
• No tools usually required — set the trivet into place over the burner until it seats securely
• Inspect mating surfaces for debris or damage before reinstalling
• If the trivet is warped or doesn't sit level after installation, do not use the burner and replace with a matched part

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

A small metal clamp that secures the refrigerator's capillary (temperature sensing) tube to the cold control so the thermostat reads temperatures accurately. Replaces worn or missing clamps to keep the sensing tube stable and prevent movement-related issues. What it does:

• Holds the capillary/sensing tube firmly against the cold control or cabinet
• Helps maintain accurate thermostat sensing by preventing tube movement
• Reduces vibration or rattling from a loose sensing tube
• Stops intermittent temperature swings caused by a displaced capillary tube

• Disconnect power before servicing the appliance.
• Handle the capillary tube gently; avoid kinks or sharp bends.
• Install clamp over the tube and secure to the control or bracket using the factory hole or fastener; do not overtighten.