Fghb2844lfs Parts

Door stop component for bottom-mount refrigerators. Prevents door from swinging too far. Replace if cracked, broken, or missing for proper operation.

Secures and supports the freezer drawer in your refrigerator, keeping it aligned and stable. Replace this bracket if yours is broken, cracked, or worn.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Replace a cracked or missing protective trim cover on your refrigerator. This cover shields internal components from dirt and restores a clean look.

Replaces worn, cracked, or missing basket trim on refrigerator baskets. Restores the finished edge and secure fit to prevent rubbing and damage.

Replacement mounting rail that supports and secures refrigerator shelves. Install when your shelf channel is cracked, bent, or allows shelves to slide out.

This replacement cover is an access panel that restores the appliance's exterior finish and protects internal components from dust and debris. It fits into the original mounting points and matches the OEM shape for a clean, factory appearance. What it does:

• Shields internal components and wiring from dirt and accidental contact
• Restores a uniform exterior surface for proper airflow and appearance
• Helps prevent small objects from entering service areas that could cause issues
• Suitable when the original cover is cracked, warped, or missing

• One replacement cover as shown

• Use basic hand tools to remove fasteners and lift off the old cover before installing the new one
• Align mounting tabs and secure with original screws; do not overtighten to avoid cracking the plastic
• Disconnect power at the breaker or unplug the appliance before servicing to avoid shock or injury
• Replace damaged mounting hardware before completing installation

This thermistor kit is the refrigerator temperature sensor assembly that monitors internal air temperature so the control can run the compressor and fans at the right times. Replaces a failed sensor to restore proper temperature sensing and cycling. What it does:

• Detects refrigerator/freezer compartment temperature and sends that signal to the control board
• Helps the control manage compressor and fan runtime for consistent cooling
• Commonly used when the fridge is not maintaining temperature or cycles erratically
• Works as the sensor portion of the evaporator/air-sensing circuit in compatible models

• Disconnect power before servicing to avoid shock or damage.
• Handle the sensor and connector gently; do not kink the sensor lead or damage the probe tip.
• Route the harness and secure clips per the original layout to ensure accurate sensing.

Covers and protects the upper door hinge area on your refrigerator. Replace if cracked, broken, or missing to restore a finished look.

This is a water supply tube that routes water through the refrigerator to components such as the ice maker or water dispenser. It provides a sealed pathway to ensure consistent water flow within the unit. Replace this tube if you notice leaking inside the refrigerator, reduced water flow to the dispenser or ice maker, or visible cracks and damage to the tubing.

Water inlet tube for bottom-mount refrigerators. Connects water supply to dispenser system. Replace if cracked, leaking, or damaged. Direct fit part.

Support bracket that secures the condenser motor in place. Replace if bent, cracked, or broken to properly stabilize the motor assembly in your refrigerator.

Rubber grommet that cushions and secures bracket components inside your refrigerator. Replace if cracked, worn, or missing to restore proper support.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.