Flce7522aw4 Parts

Fix E97 or E9C error codes, completely dead unit, or cycle malfunctions with this laundry center control board. Regulates washer and dryer functions.

This replacement housing is the body that holds the washer's detergent drawer and channels rinse water through each compartment into the tub. Replacing a cracked or warped housing restores proper dispensing and helps prevent leaks at the dispenser area.

• Supports and aligns the detergent/bleach/softener drawer
• Routes incoming water to flush each compartment into the wash tub
• Interfaces with inlet hoses and outlet chute for proper flow
• Common symptoms: water leaking from the dispenser/front panel, detergent or softener left in the drawer, poor dispensing, drawer difficult to open/close

• Disconnect power and shut off water supply before servicing
• Remove necessary panels/trim, pull out the drawer, and release mounting screws/clips to access the housing
• Label and disconnect hoses; note routing. Transfer any reusable siphon caps, seals, and the drawer from the original housing
• Reassemble, restore water and power, and run a test fill to check for leaks

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

Single replacement screw for laundry center panels, brackets, and trim. Restores secure fit when original fastener is missing, stripped, or damaged.

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

This screw fastens appliance components and panels. Replacing a missing or damaged fastener restores secure mounting and proper alignment, reducing vibration and preventing looseness that can lead to noise or premature wear.

• Secures brackets, trim, covers, or panels as designed for the unit
• Helps maintain alignment and support of mounted parts
• Replace if threads are stripped, the head is damaged, or a screw is missing
• Common symptoms include loose/misaligned panels, vibration or rattling noises, and shifting components

• Disconnect power (and shut off gas/water if applicable) before servicing
• Use the correct driver size/type and replace with the exact part number only
• Do not overtighten to avoid stripping threads or damaging plastic mounts
• When replacing multiple fasteners, remove and replace one at a time to maintain alignment

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Dryer not starting or shutting off mid-cycle? A faulty wire harness disrupts electrical signals to motors, heating elements, and controls. Moderate DIY repair.

Washer won't spin or agitate? A faulty motor assembly stops drum movement during wash cycles. This part powers agitation and spin functions in washers.

Suspension spring that supports and stabilizes the wash tub during operation. Replace if broken, cracked, or worn to restore proper tub support.

Secures the dryer door to the cabinet and provides a smooth pivot point. Replace this hinge if bent, worn, or broken to restore proper door alignment.

The Off-Balance Switch is an OEM part for Frigidaire washers. This switch is responsible for detecting vibrations and off-balance loads during spin cycles. It plays an important safety role by automatically stopping the machine if it senses excessive shaking that could damage components or cause the unit to walk or move during operation.

Symptoms of a bad off-balance switch include:

• The machine failing to detect off-balance loads and continuing to operate even with shaking
• Frequent trips of the circuit that stops the machine
• Inability to complete higher spin speeds due to sensed imbalance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Start Capacitor is an OEM part for Frigidaire combination washer/dryer laundry centers. It refers to an electronic component located within the motor control circuit board. 

This capacitor helps initiate drum movement by providing a boost of electrical current to the drive motor during appliance activation or changes in rinse/spin speed. Smooth start-ups and shifts in agitation depend on proper current delivery.

Causes of a bad start capacitor can be cracking of the outer casing from extended duty cycles or voltage fluctuations degrading dielectric plates inside over many years.

Symptoms include:

• Struggling motor that strains excessively to turn the drum
• Cycles failing to advance after starting or resume spinning  
• Unsteady or intermittent pulsing agitation noises

Replacing with a Frigidaire OEM capacitor ensures dependable motor torque for each phase of the cycle. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
 

Unresponsive control panel or display? This user interface wiring harness connects your display to the control board, restoring communication.

The Nut is an OEM part for Frigidaire washers. It secures the washer's motor in place, ensuring stability and proper functioning during operation.

A bad nut can be caused by wear and tear, damage, or improper installation. Signs of a faulty nut include the motor becoming loose, excessive vibration during operation, or unusual noises coming from the washer.

Symptoms of a bad lock nut include:

• The motor becoming loose or shifting position 
• Excessive vibration or shaking of the washer
• Unusual noises coming from the washer

Replace your worn-out or damaged nut with this genuine OEM part to restore your washer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.