Flcg7522aw4 Parts

Replacement mounting screw that fastens panels and components in laundry centers. Needed when original is missing, stripped, or damaged to restore secure fit.

Single replacement screw for laundry center panels, brackets, and trim. Restores secure fit when original fastener is missing, stripped, or damaged.

Burner orifice that meters gas flow to your dryer's burner. Replace if clogged, damaged, or wrong size for fuel type during LP/natural gas conversion.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

This replacement housing is the body that holds the washer's detergent drawer and channels rinse water through each compartment into the tub. Replacing a cracked or warped housing restores proper dispensing and helps prevent leaks at the dispenser area.

• Supports and aligns the detergent/bleach/softener drawer
• Routes incoming water to flush each compartment into the wash tub
• Interfaces with inlet hoses and outlet chute for proper flow
• Common symptoms: water leaking from the dispenser/front panel, detergent or softener left in the drawer, poor dispensing, drawer difficult to open/close

• Disconnect power and shut off water supply before servicing
• Remove necessary panels/trim, pull out the drawer, and release mounting screws/clips to access the housing
• Label and disconnect hoses; note routing. Transfer any reusable siphon caps, seals, and the drawer from the original housing
• Reassemble, restore water and power, and run a test fill to check for leaks

This screw fastens appliance components and panels. Replacing a missing or damaged fastener restores secure mounting and proper alignment, reducing vibration and preventing looseness that can lead to noise or premature wear.

• Secures brackets, trim, covers, or panels as designed for the unit
• Helps maintain alignment and support of mounted parts
• Replace if threads are stripped, the head is damaged, or a screw is missing
• Common symptoms include loose/misaligned panels, vibration or rattling noises, and shifting components

• Disconnect power (and shut off gas/water if applicable) before servicing
• Use the correct driver size/type and replace with the exact part number only
• Do not overtighten to avoid stripping threads or damaging plastic mounts
• When replacing multiple fasteners, remove and replace one at a time to maintain alignment

Washer won't spin or agitate? A faulty motor assembly stops drum movement during wash cycles. This part powers agitation and spin functions in washers.

Suspension spring that supports and stabilizes the wash tub during operation. Replace if broken, cracked, or worn to restore proper tub support.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Dryer not starting or shutting off mid-cycle? A faulty wire harness disrupts electrical signals to motors, heating elements, and controls. Moderate DIY repair.

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

The Control Board is an OEM replacement part for Frigidaire electric dryers. It is an electronic component responsible for regulating all dryer functions such as temperature, cycles, diagnostic alerts, and more. The control board receives input from sensors to monitor safety measures like heat levels and airflow.

Symptoms of a failed control board include:

• Dryer not heating or not starting cycles
• Inability to select settings or accept changes  
• Fault codes flashing in the display window
• Nonresponsive buttons or unexpected noises

Causes can include power outages over time, moisture from venting issues, or general component degradation. 

This part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore electric dryer models.

The Dispenser is an OEM replacement part for Frigidaire washing machines. Located on the interior door, the dispenser accurately releases detergent, softener, and other treatments through a series of internal chambers and slots directly into the wash drum.

Causes of failure include clogging of internal dispenser parts from built-up detergent, damaged outlets preventing proper release into the drum, worn gears interfering with controlled dispensing timing, or electronic control issues disrupting the sequenced release.  

Symptoms of a bad dispenser include:

• Products not fully dispensing or spraying inside the wash drum as intended
• Residue buildup inside dispenser compartments  
• Loose, sagging, or missing internal dispenser components
• Premature dispensing during water fill instead of correct cycle times

This OEM Frigidaire component is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Off-Balance Switch is an OEM part for Frigidaire washers. This switch is responsible for detecting vibrations and off-balance loads during spin cycles. It plays an important safety role by automatically stopping the machine if it senses excessive shaking that could damage components or cause the unit to walk or move during operation.

Symptoms of a bad off-balance switch include:

• The machine failing to detect off-balance loads and continuing to operate even with shaking
• Frequent trips of the circuit that stops the machine
• Inability to complete higher spin speeds due to sensed imbalance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Secures the dryer door to the cabinet and provides a smooth pivot point. Replace this hinge if bent, worn, or broken to restore proper door alignment.