Flefs77csb Parts

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Ratchet-style fastener secures panels and components in washer dryer combos. Replace if broken, missing, or worn to restore secure fastening.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This is a heat shield insulator that mounts on the inner side of the dryer door in a stacked laundry center or washer/dryer combo unit. It prevents excessive heat from transferring through the door during drying cycles, protecting the outer door surface and improving energy efficiency. Replace this insulation if it is torn, deteriorated, or missing, which can cause the door to become excessively hot to the touch or reduce drying performance.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

This is the blower housing that encloses the dryer blower wheel in a washer/dryer combo or laundry center unit. It directs airflow from the dryer drum through the exhaust system to properly vent heat and moisture. Replace this housing if it is cracked, warped, or damaged, which can cause poor drying performance, unusual noises, or air leaks during the drying cycle.

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

Washer overflowing or filling when off? This water inlet valve controls water flow to stop leaks and restore proper fill cycles. Moderate DIY repair.

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

Top-loading washer lid for laundry center units. Replace if cracked, bent, or no longer closes securely. Installs with hinge screws at the rear.

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.