Fph2399kf2 Parts

Instructions are no longer included with this part. See Resource Team for instructions.

This replacement access cover protects internal components and restores the appliance's finished appearance. It helps keep dust and debris out while securing wiring and mounting points for nearby parts. What it does:

• Shields internal components from dust, spills, and accidental contact
• Helps keep wiring and connectors in place and prevents snagging
• Restores a clean, finished appearance when the original cover is cracked or missing
• Reduces rattling or vibration caused by a loose or broken panel

• Disconnect power to the appliance before beginning any work
• Remove fasteners holding the old cover; save screws if they remain undamaged
• Align cover over mounting points and reinstall screws; do not overtighten
• If you encounter hidden clips or wiring, proceed slowly to avoid damage

Hex washer head ,10-32 x 0.375. Ground

No.7 plastic .375

This wiring harness is an electrical connector assembly that routes power and signals between components to restore reliable appliance operation. It replaces damaged or worn wiring to help re-establish secure electrical connections. What it does:

• Connects power and control signals between internal components to enable normal appliance functions
• Replaces frayed, melted, or broken wires that can cause intermittent operation or failure to start
• Helps resolve flickering controls, loss of power to parts, or unreliable component response
• Maintains correct routing and connector fit to prevent shorts and poor connections

• One wiring harness assembly

• Disconnect all power to the appliance before starting any repairs to avoid shock or injury
• Verify connector orientation and secure all terminal connections; do not force connectors into place
• Route the harness to match factory wiring paths and use existing clips or tie points to prevent rubbing

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

Left hand side. For the right hand side order 241674402

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Replacement screw used to secure trim, brackets and panels on compatible Frigidaire appliances. Restores proper fit to reduce rattling and keep components from coming loose for safer, more reliable operation. What it does

• Secures panels, trim pieces and small brackets so parts stay aligned and flush.
• Stops rattling or vibration caused by missing or loose fasteners.
• Prevents components from shifting or falling out during normal use.
• Works wherever the OEM screw specified by the appliance diagram is required.

• Disconnect power (and water, if applicable) before starting any repair.
• Use the correct driver and size to avoid stripping the head or threads.
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic.
• If the new screw does not seat properly, confirm this is the correct OEM part before forcing it.

This defrost drain pan collects water from the refrigerator's automatic defrost cycle and channels it safely to the evaporator area for evaporation, helping prevent leaks and water pooling beneath the appliance. What it does:

• Collects and channels defrost water away from the freezer/refrigerator cabinet
• Prevents water from pooling under the unit, which can cause floor damage or odor
• Helps proper evaporation of defrosted water at the compressor/evaporator location
• Reduces risk of ice build-up from standing water in the cabinet

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove lower access panels or kickplate to reach and replace the pan
• Inspect and clear the drain tube and heater while replacing the pan for best results
• Handle gently to avoid bending or cracking the pan

This is a replacement screw fastener used to secure panels, trim, or components on compatible Frigidaire appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or trim pieces to keep components aligned and stable
• Prevents rattling, vibration noise, and gaps caused by missing or loose fasteners
• Restores proper assembly after service or part replacement
• Helps maintain safety by keeping covers and guards firmly attached

• One screw (single fastener)

• Disconnect power or unplug the appliance before servicing
• Use the appropriate driver to avoid stripping the head; do not overtighten
• Verify the screw matches the original in length and thread before installing

This cover is a replacement protective trim piece that shields internal components and restores the appliance's finished appearance. It helps keep parts protected from dirt while improving the unit's look. What it does

• Protects exposed components and wiring from dust and debris
• Restores damaged or missing exterior trim for a finished appearance
• Helps prevent accidental contact with internal parts
• Commonly replaced when cracked, broken, or missing

• One appliance cover as pictured and specified by the manufacturer

• Disconnect power to the appliance before starting any service
• Typically attaches with clips or screws; use appropriate tools and keep fasteners
• Handle carefully to avoid scratching the replacement part