Fpm0209kf Parts

Fix a range cooling fan that won't shut off or makes howling noises with this motor. Requires removing oven from cabinet and back panel access.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Oven won't maintain temperature or exterior gets too hot? This insulation blanket contains heat and protects nearby components. Moderate DIY repair.

Microwave not heating or running weak? The capacitor stores electrical energy to power the magnetron. Common failure causes no heat or sparking issues.

Microwave not heating food? A failed magnetron is the likely cause. This tube generates the microwave energy needed for cooking. Moderate DIY repair.

This thermostat is a temperature-sensing switch used in select appliances to control operation or provide over-temperature protection. It opens or closes the circuit at a calibrated point to help maintain proper, consistent performance. What it does

• Senses temperature at its mounting/location and switches contacts at a set point
• Regulates cycling of the system or ends a heating/cooling/defrost event as designed
• Helps prevent overheating or overcooling conditions and protects components
• Supports stable, reliable operation when the original thermostat fails

• Runs continuously or won't cycle off
• Shuts off too soon or won't turn on
• Inconsistent temperature (too warm/too cold)
• Erratic cycling or failure to maintain set temperature

• 1 thermostat

• Disconnect power before servicing; allow any hot surfaces to cool
• Note wire positions; move leads one at a time to the new thermostat
• Mount in the original location and orientation; ensure firm contact/fit
• Route any sensing bulb/capillary exactly like the original; avoid kinks

Microwave door won't close or latch properly? This latch board controls the door locking mechanism to ensure secure closure during operation.

Microwave door won't stay closed or latch properly? This door latch assembly restores secure closure and proper alignment. Easy DIY repair.

This refrigerator door gasket replaces a worn or damaged outer door seal to help maintain an airtight closure and improve cooling efficiency. It restores a proper seal to reduce drafts, moisture buildup and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and water accumulation on the cabinet floor
• Reduces compressor run time by maintaining consistent internal temperature
• Common symptom: visible cracks, tears, or areas that no longer seat against the cabinet
• Common symptom: warm spots at the door edge or excess condensation

• One refrigerator door gasket

• Disconnect power to the appliance before beginning any work
• Remove the old gasket by loosening retainer screws or pulling out the retainer, then press the new gasket into the retainer channel, working around the perimeter
• For tight fits, gently warm the gasket (low heat) to make it more pliable—do not overheat or use open flame
• Inspect the seal for even seating and, if applicable, torque retainer screws to manufacturer spec

A replacement tension spring used to restore normal movement and positioning for the affected appliance component. Replaces a worn or broken spring to help parts return to their intended position and reduce loose or uneven operation. What it does:

• Provides tension or counter-force for a door, drawer or linkage so the part moves smoothly and returns to position.
• Restores alignment and prevents sagging, slamming, or parts that don't stay in place.
• Reduces noise and uneven movement caused by a stretched or broken spring.
• Useful when a worn spring causes intermittent operation or poor component response.

• Disconnect power and water before servicing. Wear eye protection and gloves — springs can release suddenly.
• Inspect mounting points, clips and anchors; replace any damaged hardware to ensure proper function.
• Use appropriate tools (needle-nose pliers, spring hook) and follow OEM instructions for safe installation.

Microwave won't turn on, made popping noise, or smells like burned electrical? The noise filter often fails when solder joints arc or short out.

Flexible door seal creates an airtight barrier to maintain proper oven temperature and energy efficiency. Replace if worn, cracked, or loose. Verify fit.

Fix an oven that won't heat, hold temperature, or has a blank display. This electronic control board restores temperature regulation and display function.

Microwave won't turn on or has no power? This fuse and holder assembly restores overcurrent protection when a blown fuse interrupts operation.

Replacement mounting screw secures panels, trim, and components in microwaves. Needed when original screws are stripped, missing, or lost during repairs.

Replacement mounting screw that secures panels, trim, and internal components in microwaves and wall ovens. Needed when screws are stripped, missing, or lost.