Frigidaire Affinity Parts

This flexible replacement hose restores proper fluid flow for the appliance by replacing cracked, clogged, or collapsed tubing. It's a direct-fit service part used where a flexible water or drain line is required. What it does:

• Carries water or discharge fluid between appliance components to enable normal operation
• Replaces damaged, cracked, or collapsed hose sections that can cause leaks
• Helps eliminate slow draining or intermittent flow caused by blockages or pinch points
• Restores a secure connection when fittings or tubing have worn

• Disconnect power and shut off water supply before starting any repair
• Inspect fittings and clamps; reuse only OEM-recommended clamps or replace if corroded
• Route hose without sharp bends or kinks and secure to prevent rubbing or chafing

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This mounting bracket secures its associated component inside your appliance, keeping it properly positioned during operation. Replacing a bent or broken bracket helps stop rattling or vibration and restores stable, reliable performance.

• Provides a rigid mounting point to the appliance frame or assembly
• Maintains correct position and alignment of the attached component
• Helps reduce vibration and operational noise
• Common failure signs: cracks, bending, stripped holes, or the part no longer stays secured

• Disconnect power before servicing; if working on a washer, also shut off water supply
• Note the original orientation and hardware locations; transfer any clips or grommets from the old bracket
• Reinstall using existing screws and tighten evenly—do not overtighten

This mounting bracket secures internal components or panels to the appliance, restoring proper alignment and support. Designed to replace a damaged or missing bracket so doors, drawers or internal assemblies sit and operate correctly. What it does:

• Provides structural support for panels, drawers or internal components
• Restores proper alignment to reduce rattling, sagging or binding
• Replaces broken, bent or missing brackets that prevent parts from seating
• Helps maintain safe operation by keeping components firmly attached

• One mounting bracket

• Disconnect power and water before starting repairs
• Use appropriate fasteners; retain any original screws if undamaged
• Inspect surrounding mounting points for damage and replace if needed
• Wear gloves to protect against sharp edges; test fit before final fastening

This air chamber directs refrigerated air from the freezer to the fresh food section to help maintain consistent temperatures and proper airflow. It replaces a cracked or damaged diffuser that can disrupt cooling performance. What it does:

• Channels cold air through the refrigerator compartments for balanced cooling
• Helps prevent temperature imbalance and warm spots in the fresh food area
• Reduces uneven frosting or condensation caused by airflow leaks
• Restores intended airflow path when the original chamber is broken or missing

• Disconnect power to the appliance before starting any repair
• Typically installs behind interior liners; remove shelves and panels as needed for access
• Handle the part and surrounding trim carefully to avoid damaging clips or seals

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

This is a motor-mount screw used to secure the appliance motor housing. It's a direct-fit fastener that restores proper motor attachment to reduce movement and rattling caused by loose or missing hardware. What it does:

• Secures the motor to its mounting bracket or housing
• Prevents motor shifting that can cause vibration, noise, or misalignment
• Restores proper mechanical connection after strip-out or lost hardware
• Helps maintain safe operation by keeping motor fastened

• Disconnect power before servicing the appliance.
• Use the correct screwdriver or socket to avoid stripping the head.
• Thread carefully and tighten to snug; avoid over-tightening which can strip threads.
• If mounting holes or threads are damaged, repair or replace the affected components before reinstalling.

This O-ring is a small rubber seal that helps prevent water or refrigerant leaks by creating a tight connection between mating parts. Replacing a worn O-ring restores a secure seal and reduces dripping or loss of pressure. What it does:

• Forms a leak-tight seal at a joint or fitting to stop drips and seepage
• Helps maintain proper fluid or refrigerant pressure where used
• Commonly replaced when cracked, flattened, or hardened
• Can eliminate intermittent leaks that occur under load or when the appliance cycles

• Turn off and unplug the appliance and shut off water or refrigerant supply before service
• Inspect mating surfaces and replace any damaged fittings to ensure a proper seal
• Lightly lubricate the O-ring with appliance-safe silicone grease; avoid petroleum-based products
• Do not stretch or nick the O-ring during installation; confirm correct seating before restoring power or supply

This replacement cushion is a small rubber bumper that protects components and reduces vibration and noise where panels, doors, or assemblies meet. It helps keep parts aligned and prevents metal-on-metal contact. What it does:

• Absorbs shock and reduces vibration to minimize rattling or movement
• Protects surfaces from wear and prevents scraping or chafing
• Helps maintain proper spacing or alignment of panels or assemblies
• Works wherever a soft bumper or spacer is required

• Disconnect power to the appliance before servicing.
• Remove any covers or panels to access the mounting area.
• Press or seat the cushion into the locator/receptacle; replace retainers if present.

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This bushing is a small sleeve bearing that supports a rotating shaft and reduces metal-to-metal wear, helping restore smooth, quiet operation and proper alignment in the appliance. What it does:

• Supports and centers a rotating shaft or post to prevent wobble and friction
• Reduces wear between moving metal parts for smoother operation
• Helps stop squeaks, grinding noises, or rubbing caused by a worn support
• Restores proper alignment to improve component life and performance

• Disconnect power or unplug the appliance before starting any repair
• Inspect surrounding components and replace any visibly worn parts for best results
• Press or tap the bushing into place squarely; avoid deforming the sleeve during install