Frigidaire Affinity Front Load Washer Parts

Mounting bracket secures internal components and panels in your washer. Replace if bracket is cracked, broken, or missing to restore proper alignment and support.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This suspension spring supports the washer tub and helps stabilize the drum during spin cycles to reduce vibration and noise. Replaces a worn or broken tub spring to restore smoother operation. What it does

• Holds and stabilizes the inner tub assembly to limit excessive movement during spins
• Helps reduce vibration and rattling that can occur from a loose or broken spring
• Prevents tub misalignment that can cause rubbing or noise
• Works with the washer's suspension system to maintain proper spin balance

• One suspension (tub) spring as shown

• Disconnect power and water supply before starting any repairs
• Springs are under tension; use caution and proper tools to remove/install
• Inspect other suspension components (shocks/rods, mounts) and replace if worn

Fix a washer that loses power, won't spin properly, or has an unresponsive control panel. This electronic control board restores normal operation.

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Secures the motor housing to its mounting bracket in washers and laundry centers. Replace if screw is missing, stripped, or damaged during service.

Rubber O-ring seal prevents water leaks at hose connections and fittings. Replace when worn or cracked to restore tight seal and stop dripping. Verify fit.

Sleeve bearing bushing that supports rotating shafts in washers. Replace if worn, cracked, or causing noise. Reduces friction and centers components.

Replacement mounting bracket that secures washer panels and components. Needed when original bracket is cracked, broken, or missing, causing loose or misaligned parts.

Replace a cracked, broken, or worn washer door transition ring. This trim piece covers the gap where the door meets the cabinet for proper alignment.

This electronic control is the oven's main user interface and timing/temperature manager, restoring oven functions and display responsiveness for safe, reliable cooking. It replaces a failed control module to bring back normal oven operation. What it does:

• Manages oven temperature sensing, bake/broil cycles, timers and user commands
• Controls the oven display, clock, and front-panel touch/key inputs
• Stops oven heating or cancels cycles when internal control fails or shows errors
• Common symptom fixes: blank or unresponsive display, inaccurate temps, oven not starting, or error codes tied to the main control

• One electronic control assembly

• Disconnect power to the appliance before starting work to avoid shock or damage
• Handle the board carefully; avoid touching circuitry and use anti-static precautions when possible
• Some units may require front-panel reassembly or minor adjustments after swap;

Hex washer head screw secures panels, brackets, and drum assemblies in washers. Replace rusted, stripped, or missing screws to prevent rattling.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.