Frigidaire Lfss2312tp4 Parts

Replacement screw for securing refrigerator panels, brackets, and trim. Needed when original fastener is missing, stripped, or damaged during repairs.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

This adhesive control-box label replaces a missing or damaged identification/sticker on the appliance control enclosure, restoring legible part, wiring and safety markings so the control area can be identified during service. What it does:

• Replaces faded, torn or missing identification and safety markings on the control box
• Restores printed part and wiring callouts used for troubleshooting and repairs
• Helps technicians confirm control-box location and basic service information
• Prevents confusion from illegible or peeling labels during maintenance

• Disconnect power to the appliance before doing any service or label replacement
• Clean and dry the control-box surface; remove dirt, grease, and loose material for best adhesion
• Peel backing and carefully align the label before pressing firmly to set
• Do not place over moving parts, ventilation openings, or heat sources; replace only as intended by OEM

Supports the refrigerator door pivot for smooth opening and closing. Replace this bearing if worn, cracked, or causing door misalignment or noise.

Metal flat washer for refrigerator ice maker auger and other assemblies. Replaces worn, missing, or damaged washers during repairs and reassembly.

Replacement screw for securing refrigerator panels, brackets, and trim. Restores proper fit and reduces rattling from loose or missing fasteners.

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

Limits refrigerator door swing to prevent over-extension. Replace if broken, cracked, or missing to restore proper door alignment and protect hinges.

Replacement mounting screw secures trim, brackets, and panels inside your refrigerator. Restores proper fit when original screws are missing or stripped.

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

White plastic hinge cover that snaps onto your refrigerator door hinge. Replace if cracked, broken, or discolored to restore a clean appearance.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components