Frs23h5asbb Parts

This cabinet corner trim is a replacement corner piece that restores the finished edge of the appliance cabinet for a clean, protected look. It helps cover damaged or worn corners and improves the cabinet's appearance. What it does:

• Replaces a cracked, chipped or missing cabinet corner trim to restore a smooth finished edge
• Protects the cabinet corner from dings, moisture, and dirt buildup
• Improves cosmetic appearance by covering exposed cabinet edges
• Keeps adjacent panels aligned and reduces visible gaps around the cabinet corner

• Disconnect power to the appliance before working near electrical components
• Remove any damaged trim and clean the mounting area before installing the new piece
• Trim may snap into place or secure with screws/adhesive depending on model—use appropriate fasteners

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

Left hand side. For the right hand side order 241674402

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

#10 pan head 8 - 18 x .5

Color: Black/natural. Nylon

Right hand side. For the left hand side order 241674401

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This control rod bracket secures the control rod to the appliance, restoring proper linkage and part alignment for reliable operation. Designed to replace a worn or broken mounting bracket and stabilize control movement. What it does:

• Holds the control rod in place so levers and linkages operate smoothly
• Restores proper alignment when the rod is loose, bent, or detached
• Helps eliminate binding or intermittent actuator movement caused by a damaged bracket
• Supports consistent mechanical operation of the connected control components

• One control rod mounting bracket

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Remove any panels or covers as needed to access the bracket; keep fasteners organized for reassembly
• Inspect adjacent linkage and fasteners; replace any damaged clips or screws for a secure fit