Frs26lh5dwo Parts

This small but critical actuator spring restores return tension in a refrigerator's actuator mechanism, helping the lever reset to neutral after use so controls feel responsive and operation stops cleanly. What it does:

• Provides the return force for an actuator or lever so it moves back to its neutral position
• Helps the mechanism engage/disengage a switch cleanly
• Common symptoms of a weak or broken spring: lever sticks, feels loose, or doesn't spring back
• Contribute to intermittent activation or failure to stop when released

• 1 actuator spring

• Disconnect power; if working near the dispenser/water system, shut off the water supply
• Access the actuator mechanism and note the spring's exact orientation (take a photo before removal)
• Use needle-nose pliers to transfer the spring; do not over-stretch or deform it
• Wear cut-resistant gloves and eye protection; test lever return action before reassembly

Inlet valve filter

Color: White

Specs: 1.40`` long

This spacer fits the refrigerator door hinge to set proper clearance and alignment so the door swings smoothly and seals correctly. Replace a worn or missing spacer to eliminate rubbing and uneven gaps at the door.

• Maintains the specified distance between hinge components for correct door height and alignment
• Helps the door open and close without rubbing or binding
• Supports consistent gasket contact for a reliable seal
• Common signs of wear: door sagging, scraping noises, uneven gaps, or the door not closing flush

• Unplug the refrigerator; remove items from the door and support the door before working on the hinge
• Note the order of any washers, cams, and spacers during disassembly for correct reassembly
• Reinstall hardware in the same sequence; do not overtighten fasteners to avoid deforming the spacer
• After reassembly, check door alignment and gasket seal; adjust as needed

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This spiral pin secures components in place within the appliance assembly, providing a tight, durable fit that resists loosening under normal operation. Replacing a worn or missing pin helps restore proper alignment and dependable drive of the linked parts.

• Holds mating parts together with a press-fit connection
• Can help resolve issues like loose or slipping drive components, rattling, or intermittent operation in the affected mechanism
• Maintains correct alignment to reduce wear on adjoining parts

• Disconnect power and shut off water before servicing
• Support the assembly to relieve tension before removing the old pin
• Use the correct size punch/driver to press the pin out and in straight
• Do not force; inspect mating parts for wear and replace if damaged

Replacement water inlet tube that connects the refrigerator water inlet valve to the inline filter, restoring proper water routing for the dispenser and ice maker while helping prevent leaks and maintain steady water flow. What it does:

• Routes water from the inlet valve to the fridge's inline filter for filtration and delivery.
• Restores or improves water flow when the original tubing is cracked, pinched, or clogged.
• Helps stop leaks caused by damaged or brittle tubing between the valve and filter.
• Common symptoms indicating replacement: reduced or no water flow, visible leaks, or damaged/kinked tubing.

• Turn off the water supply and unplug the appliance before replacing tubing.
• Use appropriate fittings/clamps and avoid kinking or over-bending the tube; replace worn clamps if present.
• Tighten connections securely but do not overtighten plastic fittings; check for leaks after restoring water and power.

This kickplate grille mounts across the bottom front of the refrigerator. It restores a finished look and helps protect the machine compartment while allowing proper airflow through the condenser area.

• Covers the lower front opening to hide and shield internal components
• Vents air to support proper condenser airflow
• Replaces a damaged, cracked, or missing kickplate
• Common symptoms: broken tabs, grille won't stay attached, visible damage, missing piece

• Disconnect power before servicing
• Open doors to clear the grille; remove the old piece by releasing clips or removing screws
• Align the new grille with the mounting points and snap or fasten into place
• Ensure the grille sits evenly and doesn't interfere with door swing or airflow

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

This spacer is a small positioning piece used in refrigerator assemblies to maintain proper clearance and alignment between parts. Replacing a worn or missing spacer helps restore smooth operation and prevents rubbing or binding. What it does:

• Maintains the designed gap between mating parts to prevent friction and wear
• Helps keep assemblies aligned for smooth, consistent movement
• Reduces looseness, rattling, or poor fit caused by a missing or deformed spacer
• Typical signs include visible damage or a missing spacer and misalignment or scraping noises in the area it installs

• 1 spacer

• Disconnect power; if working near water components, shut off the water supply
• Use your model's parts diagram to determine exact location and orientation
• Retain and reuse original fasteners or clips unless damaged
• Do not overtighten hardware; ensure smooth operation after installation

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

Specs: .875`` long

Replacement ice bin rail that supports and guides the freezer ice bin for smooth sliding and secure positioning. Restores proper bin alignment so the ice bin removes easily and reduces binding, rattling, and accidental drops.

• Supports and guides the ice bin so it slides in and out without sticking
• Keeps the bin properly aligned to prevent tipping or falling when removing
• Reduces noise caused by a loose or worn support rail
• Commonly replaced when the bin binds, catches, or sits unevenly

• Disconnect power to the appliance before beginning any work
• Remove the ice bin and any loose ice before removing the old rail
• Install by seating the rail into the mounting locations and securing with the original fasteners; basic hand tools may be required

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used