Frs6hr45kso Parts

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Replacement water reservoir tank for side-by-side refrigerators. Stores and supplies water to the dispenser and ice maker. Replace if cracked or leaking.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Replaces damaged or worn refrigerator wiring harness. Restores electrical connections between components. Order this part if your harness is frayed or broken.

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Secures the micro switch in your refrigerator's ice dispenser assembly. Replace if screw is rusted, stripped, or missing to properly mount the switch.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Electronic control panel that mounts in the refrigerator compartment to manage appliance functions. Replace if cracked, unresponsive, or damaged.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Wiring harness for refrigerators. Connects electrical components inside the appliance. Replace if wires are damaged, frayed, or connections are loose.

Support plate for freezer interior mounting. Replaces cracked, broken, or missing support plates that compromise shelf or component stability.