Frs6l7js2 Parts

Refrigerator not cooling or running too warm? A faulty thermostat prevents proper temperature regulation. This control cycles the compressor to maintain set temps.

Refrigerator door bin versashelf that mounts inside the door to hold condiments, bottles, or eggs. Replace if cracked, broken, or missing from your unit.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

This rear cover replaces the damaged or missing cabinet back panel to protect internal components and restore a finished appearance. It helps keep wires and motors shielded and prevents debris from entering the appliance. What it does:

• Shields the appliance's rear components (motor, wiring, vents) from dust and physical damage
• Restores proper airflow routing and helps reduce rattling caused by loose or broken panels
• Prevents accidental contact with internal electrical components and moving parts
• Common symptom: cracked, warped, or missing rear panel; noticeable noise, drafts, or exposed wiring

• Disconnect power before starting any work
• Removal typically requires backing out screws and lifting the old panel away; keep fasteners for reuse if undamaged
• Handle edges carefully to avoid cuts; wear gloves and eye protection
• Verify panel aligns with existing screw bosses and clips; do not force into place—confirm fit before tightening

Replacement control panel label for your refrigerator. Restores the worn, faded, or peeling label on the control panel interface. Direct fit part.

Front housing cover for refrigerator control box assembly. Mounts in food compartment with light and damper. Replace if cracked, broken, or damaged.

Replacement electrical harness for your refrigerator. Connects power to internal components. Order a new harness if yours is damaged, frayed, or corroded.

Mounting plate secures the ice maker assembly inside your refrigerator. Replace if cracked, warped, or broken to restore proper ice maker support.

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

Outer door panel for refrigerator. Replaces cracked, dented, or damaged exterior door shell. Does not include shelves, handle, or hinges—door panel only.

Secures water, drain, and refrigerant tubing to prevent movement and wear. Replace if tubes are loose, vibrating, or damaged. Verify fit with model number.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.