Fsc23f7tdwo Parts

This genuine replacement clip secures appliance components to keep panels and small parts aligned and stable, restoring fit and function. It's a small, durable fastener used where a simple snap or hold is required. What it does

• Holds trim, panels, or small components in place to prevent rattling or misalignment
• Restores secure fit where a damaged or missing clip causes loose parts
• Helps stop vibration noise caused by unsecured pieces
• Small, direct-fit part—replaces a single broken or lost clip

• Disconnect power to the appliance before starting any repair.
• Access may require removing trim or panels; keep track of fasteners.
• Press or snap the clip into place; do not force beyond fit—if it won't seat, recheck alignment.
• Wear gloves and eye protection to avoid cuts from sharp edges.

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This part is a dispenser control board designed for Frigidaire refrigerators. The control board regulates the water and ice dispenser, allowing users to control whether ice is cubed or crushed, and turning the light on or off. Over time, the control board may be exposed to moisture, causing it to corrode and fail. Exposure to excessive heat can also lead to damage.Signs that the dispenser control board may need to be replaced include none of the dispenser functions operating, or dispenser functions operating inconsistently or intermittently. If erroneous operation is noticed, users will need to replace the dispenser control board. This will require a flathead screw driver to pry the panel off the front. The control board should be visible underneath. Disconnect the wires, taking note of their location and orientation, and then remove the board. Install the new one, replace the wires, and then replace the cover.This genuine OEM part is sold individually. It is compatible with Frigidaire, Kenmore, and Crosley models.

This condenser fan motor circulates air across the condenser coils to help remove heat from the refrigeration system, improving cooling efficiency and preventing overheating of components. What it does

• Spins the condenser fan blade to move air over condenser coils for proper heat rejection
• Helps maintain compressor and system temperatures during normal cooling cycles
• Can cause warm cabinet temperatures or noisy operation when worn or seized
• Stops cycling correctly if the motor fails, which may lead to extended run times

• Disconnect power to the appliance before starting any service.
• Handle sharp condenser fins and mounting hardware with care; use gloves as needed.
• Verify fan blade clearance and secure all mounting screws before restoring power.
• After installation, the motor runs quietly and the fan blade spins freely.

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly

This membrane switch is the flat control-panel overlay that provides the touch/button interface for the appliance, restoring proper button response and user control when the original keypad is worn or unresponsive. What it does:

• Replaces a worn or damaged keypad overlay so button presses register reliably
• Restores tactile contact for touch or soft-button controls on the appliance console
• Can resolve intermittent or non-responsive buttons caused by a degraded membrane
• Helps return normal operation to timed, temperature, and function inputs

• One membrane switch/control panel overlay

• Disconnect power to the appliance before beginning any service
• Installation typically requires removal of the control console or front panel; handle the flexible membrane carefully to avoid creasing
• Ensure the replacement aligns correctly and the connector is seated firmly; do not force components
• If problems continue after installation, the underlying electronic control board may also need inspection