Gas95566as Parts

This compressor start device is the relay-and-overload assembly that helps your refrigerator's compressor start and protects it from overheating. Replacing a failing start device can stop repeated clicking and help restore consistent cooling performance.

• Provides the initial start circuit for the compressor, then disengages once running
• Protects the compressor by opening on overcurrent/overheating (overload protection)
• Helps address symptoms like: compressor won't start, repeated clicking, and warm fridge/freezer
• Often found heat-damaged or cracked when failed

• Disconnect power before servicing; access the compressor compartment at the rear
• Note wire positions; pull the old start device straight off the compressor pins
• Transfer wires to the new device; push it fully onto the compressor terminals until seated
• Reinstall the rear cover and restore power; verify normal compressor start

The Grommet and Gasket Assembly is an OEM part for GE refrigerators. It is designed to create a secure seal around various refrigerator components, preventing air leaks and ensuring efficient operation. This assembly typically includes both the grommet and gasket, which work together to maintain the refrigerator's internal temperature and prevent moisture and contaminants from entering.

You should replace the grommet and gasket assembly if it becomes worn out or damaged. Causes of a bad grommet and gasket assembly can include regular wear and tear, exposure to temperature fluctuations, or physical damage that leads to cracks or deformities. A compromised seal can result in inefficient cooling and increased energy consumption.

Symptoms of a bad grommet and gasket assembly include:

• Air leaks around the refrigerator door or components
• Increased energy bills due to inefficient cooling
• Frost or condensation buildup inside the refrigerator
• Difficulty in maintaining the desired temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Evaporator Fan Rear Bracket is an OEM part for GE refrigerators. It supports and secures the evaporator fan at the rear of the refrigerator, ensuring it operates correctly to circulate air throughout the appliance.

Causes of a bad evaporator fan rear bracket can include physical damage due to impact, wear and tear from prolonged use, or corrosion from exposure to moisture.  

Symptoms of a bad evaporator fan rear bracket include:

• Unusual noises coming from the rear of the refrigerator
• Reduced cooling efficiency
• The evaporator fan becoming loose or detached
• Vibrations or rattling noises during operation

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This defrost heater assembly melts frost from the evaporator during the automatic defrost cycle to keep airflow clear and temperatures stable. Replacing a failed heater helps restore consistent cooling and prevents ice buildup that blocks the freezer wall. What it does:

• Heats the evaporator coil to melt accumulated frost/ice during scheduled defrosts
• Keeps airflow paths clear to maintain proper temperatures
• Helps prevent excessive frost on the back panel or evaporator
• Common symptoms of a failed heater include heavy ice buildup, weak airflow, warmer fresh-food temps, and longer run times

• 1 defrost heater assembly

• Unplug the refrigerator before servicing; wear gloves—sheet metal edges can be sharp
• Access the heater behind the freezer's rear panel at the evaporator
• Note wire routing and connector orientation; secure the new element as originally mounted
• After installation, clear any remaining ice so airflow is restored before powering on

The Refrigerator Shelf is an OEM part for GE refrigerators. This shelf provides sturdy and adjustable storage space within the refrigerator, allowing you to organize food and beverages efficiently.  

Causes of a bad refrigerator shelf can include cracks or breaks from heavy items, wear and tear from regular use, or damage from accidental impacts during cleaning or rearranging.

Symptoms of a bad Refrigerator Shelf include:

• Cracks or fractures in the shelf
• The shelf not fitting securely in its slot
• Difficulty in adjusting the shelf height
• The shelf sagging or unable to hold weight properly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Restore accurate temperature regulation with this cold control kit. It replaces a worn or unresponsive refrigerator temperature control so the unit cycles on and off correctly and maintains food-safe, consistent cooling.

• Regulates internal temperature by cycling the compressor and fans based on setpoint
• Helps resolve symptoms like fridge too warm, too cold, or not cycling off
• May correct intermittent cooling or temperature swings due to a failed control
• Designed as a service kit to update or replace the original cold control assembly

• Unplug refrigerator before service; handle sharp sheet metal with care
• Access control from the fresh food control housing; note wire positions and capillary routing
• Avoid kinking or sharply bending the capillary tube during removal/installation
• After installation, set to a mid setting and allow 24 hours to stabilize temperature

This Hi-Lo truss-head screw secures plastic and sheet-metal components in your refrigerator. Replacing stripped or missing fasteners restores a tight, rattle-free fit and keeps brackets, trim, and covers properly aligned.

• Fastens brackets, panels, trim, covers, and other components to the cabinet or liner
• Hi-Lo thread design grips plastic or thin metal for a strong, reliable hold
• Helps address loose or vibrating parts, rattling noises, and misaligned covers
• Direct replacement for a missing, worn, or damaged mounting screw

• Disconnect power before servicing any appliance
• Support the part being secured to avoid stress or misalignment
• Start the screw by hand to prevent cross-threading; use the correct driver
• Snug firmly but do not overtighten, especially when threading into plastic

The Vegetable Pan Humidity Slide is an OEM replacement part for GE refrigerators. This slide is designed to allow control of the humidity levels within the vegetable pan to keep your fruits and vegetables fresh for longer periods. By sliding the control lever, you can create the ideal moisture level for different types of produce.

A bad vegetable pan humidity slide can occur due to regular use or accidental damage. If you notice that the humidity levels are not adjustable or if the slide is broken or missing, it may indicate a need to replace this part.

Symptoms of a bad vegetable pan humidity slide include:

• Inability to adjust the humidity levels in the vegetable pan
• Produce wilting or spoiling faster than usual
• Difficulty in maintaining freshness and crispness

Restore your refrigerator by replacing the faulty vegetable pan humidity slide with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This bottom hinge supports the refrigerator door at the lower pivot point, keeping it aligned so it opens smoothly and seals correctly. Replace a worn hinge to restore proper closure and help maintain an airtight door seal.

• Provides the lower pivot and support for the door
• Helps maintain alignment for consistent gasket contact and smooth swing
• Wear or damage can cause door sagging, rubbing, or incomplete closure
• Misalignment can lead to air leaks and temperature fluctuations
• Clicking, grinding, or loose movement near the hinge may indicate wear

• Unplug the refrigerator; turn off water to the dispenser/ice maker
• Remove door bins/contents and support the door to prevent strain on wiring or tubing
• Remove the lower hinge cover, note shim/spacer locations, and transfer them to the new hinge
• Reinstall hardware, align the door, and ensure the gasket seals evenly all around

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This replacement clamp secures lines or components inside the refrigerator, keeping them properly routed and stable. Replacing a broken or missing clamp helps reduce vibration and prevents rubbing damage or leaks from loose tubing. What it does:

• Holds tubing or wiring harnesses securely in place inside the refrigerator
• Maintains correct routing and clearance to prevent chafing and wear
• Helps reduce vibration and rattling noises from unsecured lines
• Can help prevent drips or leaks when used to retain water tubing

• 1 clamp

• Unplug the refrigerator and, if working with water lines, shut off the water supply
• Note the original clamp orientation and routing; take a photo before removal
• Install the new clamp in the same location, securing lines without pinching or over-stressing them
• Restore power (and water if applicable) and check that lines are secure; inspect for leaks if used on water tubing

This small donut-shaped gasket fits where specified in your refrigerator's parts diagram to create a tight seal between mating components. Replacing a worn gasket helps stop minor leaks and restore a secure fit.

• Forms a tight seal at the designated joint or fitting
• Helps prevent seepage or drips from a compromised connection
• Replaces a brittle, cracked, flattened, or missing original gasket
• Supports proper assembly alignment and a snug fit

• Unplug the refrigerator and, if servicing the water system, shut off the water supply
• Note the gasket's original placement and orientation before removal
• Clean mating surfaces; lightly moisten the new gasket to ease seating
• Reassemble without overtightening; restore power/water and check for leaks

The Control Temp is an OEM component specifically designed for GE refrigerators. It enables precise temperature regulation within the refrigerator. 

The control temperature sensor monitors interior conditions and sends feedback to the control board regarding temperature deviations. Based on sensor readings, the board triggers the cooling system accordingly to maintain the desired set point. 

Symptoms of a bad control temp sensor include:

• Fluctuating interior temperatures that cannot be stabilized
• The cooling system running inconsistently or excessively  
• Inability to accurately adjust or maintain set temperature levels

Causes can relate to sensor failure over time due to age, thermal stress from freezing/thawing, or physical damage.

This genuine OEM GE replacement part ensures the control system has accurate temperature input to function optimally. Compatible with Hotpoint, RCA, and Kenmore refrigerator models as well. Replace yours to restore reliable cold storage performance.
 

The Air Tower and Evaporator Cover Assembly is an OEM part for GE refrigerators. This multi-piece component is located inside the refrigerator compartment and manages airflow that travels through the evaporator coil area. An attractive cover protects inner workings while directing optimal temperature control.  

Symptoms of a bad air tower assembly include:  

• Audible air disturbances accompanied by inconsistent interior temperatures
• Buildup of frost or moisture collecting outside the evaporator area
• Inability of warm food to adequately cool down inside the fridge  

Causes relate to cracks developing in thermoplastic covers after years of climate cycling strains. Closed airways may become obstructed as well affecting circulation.

This GE OEM replacement restores reliable humidity management and product cooling. Its enduring construction circulates purified air for consistent food holding at proper temperatures per federal guidelines. Compatible with GE and select Kenmore side-by-side models for direct fit airflow performance.
 

This plastic water tube routes water inside your refrigerator to the dispenser and/or ice maker. Replacing a cracked, brittle, or leaking tube restores proper water flow and helps prevent leaks and water damage.

• Directs water between components such as the inlet valve, reservoir, door, dispenser, or ice maker (varies by model)
• Maintains a sealed, food-grade path to prevent leaks and air intrusion
• Damage can lead to puddles behind/under the fridge or inside the fresh food compartment
• Common symptoms: slow/no dispenser flow, ice maker not filling or making small cubes, visible cracks/kinks

• Unplug the refrigerator and shut off the household water supply; relieve line pressure at the dispenser
• Note tube routing and connection points before removal; avoid sharp bends and kinks during install
• Cut tube ends square and fully seat into compression or push-in fittings
• Restore water, check all joints for leaks, and run water to purge air from the system