Gas95566as Parts

A replacement freezer door panel that restores the exterior finish and sealing surface on compatible refrigerators. Helps maintain proper cold retention and gives a clean, uniform appearance to the freezer compartment. What it does:

• Replaces a cracked, dented, or discolored freezer door panel to restore look and function
• Provides the outer surface that mates to the freezer door assembly and trim
• Helps maintain an even seal and reduces cold air loss when the door closes
• Useful when a door panel is damaged by impact or cosmetic wear

• One white freezer door panel

• Basic door trim removal and reassembly required; retain all fasteners and clips for reuse if undamaged
• Disconnect power to the appliance before starting work to avoid electrical hazards
• Handle panel carefully to avoid scratching the finish; use protective gloves and a soft surface
• If the door contains internal components (liners, insulation, hinges), reattach per manufacturer instructions

This replacement power cord connects your range or oven to the household electrical outlet, restoring safe, reliable power and helping the appliance run normally. Designed to match OEM fit and function where specified. What it does:

• Supplies main electrical power to the range/oven so burners, oven and controls can operate.
• Replaces frayed, cut or heat-damaged cords that can cause intermittent power or visible damage.
• Helps resolve symptoms such as the appliance not powering on, tripped breakers when plugged in, or visible cord damage.
• Restores a secure cord connection when the original cord or strain relief is loose or worn.

• One replacement power cord.

• Always disconnect power at the breaker before inspecting or replacing the cord.
• Route the cord and secure the strain relief per the appliance's installation instructions.
• Tighten terminal connections firmly and confirm no bare wires are exposed.

This autofill pitcher is the replacement water reservoir that holds and delivers filtered water for compatible refrigerator systems, restoring normal automatic-fill function and convenient chilled water access. What it does:

• Replaces the internal reservoir that stores filtered water for the refrigerator's autofill feature
• Restores steady automatic refilling so the dispenser and pitcher have ready chilled water
• Helps resolve symptoms like reduced or no water available in the pitcher or inconsistent autofill
• Works with the refrigerator's built-in fill valve and filter system to maintain supply

• Disconnect power to the refrigerator or follow manufacturer safety instructions before servicing
• Remove and replace the pitcher assembly per the refrigerator's service instructions; avoid forcing or over-tightening connections
• Inspect gaskets/seals and the fill valve area for debris or damage while installing
• Flush/dispense a few quarts of water after installation per OEM guidance to clear air and any loose particles

This refrigerator door stop cushions and limits the door swing to prevent over-travel and protect the cabinet and hinge. Durable plastic design restores proper door alignment and reduces slamming for a quieter, safer fridge. What it does

• Replaces a worn or broken door stop to stop the door from swinging too far.
• Helps prevent damage to the cabinet edge and hinge by absorbing impact.
• Reduces door noise and improves door alignment for a consistent seal.
• Commonly used where the original plastic stop is cracked, missing, or worn.

• One refrigerator door stop (white), as shown.

• Basic hand tools typically required; disconnect power only if working near electrical components.
• Keep original fasteners; replace only with like hardware if specified.
• Inspect surrounding hinge and mounting area for wear and replace if necessary.

This U-shaped clip secures trim and components in place on compatible GE appliances, helping keep panels and assemblies aligned for reliable operation. Simple replacement when a broken or missing clip causes loose trim or rattling. What it does:

• Holds trim, panels or small assemblies in position to prevent movement
• Restores secure fit where a worn or broken clip allows gaps or vibration
• Helps eliminate rattling, misaligned doors, or loose internal components
• Works as a direct-fit replacement for the same OEM clip design

• One U-shaped retaining clip

• Turn power off and unplug the appliance before accessing panels or parts
• Remove any trim or screws carefully to reach the clip location; retain fasteners
• Clip typically snaps into place; replace any damaged surrounding hardware

This foam gasket seals and cushions the supply nozzle to help prevent leaks and reduce vibration where the nozzle meets the appliance. It's a small, soft replacement part used to restore a proper seal and fit. What it does:

• Seals the nozzle connection to help stop drips or slow leaks around the nozzle area
• Cushions and stabilizes the nozzle to reduce rattling or vibration noise
• Restores correct spacing and alignment for reliable fluid flow
• Used when foam is compressed, split, or missing and no longer provides a seal

• One nozzle supply foam gasket

• Disconnect power and shut off water supply before replacing
• Remove surrounding trim or components as needed to access the nozzle area
• Clean mating surfaces and seat the foam squarely for a proper seal
• No special tools required; handle gently to avoid tearing the foam