Gb2 Parts

This humidity control slide mounts in the crisper cover and moves the vent door to adjust airflow in the drawer. Replace a broken or missing slide to restore smooth adjustment and help manage moisture for better produce storage.

• Controls the crisper vent to increase or decrease humidity
• Provides the user-facing lever for Low/High humidity settings
• Helps reduce excess condensation, sogginess, or drying in the drawer
• Common symptoms: slide cracked or missing, hard to move, won't stay in position, humidity setting has no effect

• Unplug the refrigerator before servicing
• Remove the crisper drawer and lift off the cover/shelf as needed
• Release the old slide from its retainers (a small flat-blade screwdriver may help) and note the linkage to the vent
• Snap in the new slide, confirm smooth travel end to end, then reassemble

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

This factory screw secures appliance panels, brackets, or trim. Replace a missing, stripped, or rusted fastener to restore a tight, rattle-free fit and keep components properly aligned in the intended OEM locations. What it does

• Fastens brackets, trim, or sheet-metal panels to the chassis
• Replaces worn, rusted, or missing hardware
• Helps eliminate loose panels, vibration, and misalignment
• Restores proper fit and support for affected assemblies

• Includes 1 screw

• Disconnect power and shut off gas/water before servicing
• Match this screw to the original location; lengths and thread types can vary by position
• Use the correct driver; start by hand and do not overtighten to avoid stripping threads
• If the receiving threads are damaged, repair/replace the mating clip or insert before installing

This replacement dairy door restores the flip-up cover for the small butter/dairy bin on your refrigerator door. Replace a cracked or missing cover to keep contents contained and your door storage tidy.

• Covers the butter/dairy compartment on the fresh food door
• Flips up for access and down to help secure items
• Helps prevent small items from sliding out of the bin
• Replaces a cracked, broken, loose, or missing cover

• Remove the dairy bin for easier access and alignment
• Align hinge tabs with the bin pivots and press gently until it snaps in
• Avoid forcing cold plastic; let parts warm to room temperature
• If working near electrical components, disconnect power and wear cut-resistant gloves

This humidity control body is the fixed housing for a refrigerator crisper vent. It mounts to the crisper cover or drawer and provides the track for the slider so you can open/close the vent and help manage drawer moisture. What it does:

• Serves as the stationary housing for the crisper's humidity control vent
• Guides and secures the humidity control slider so it moves smoothly
• Helps regulate airflow into the crisper to influence moisture levels
• Common signs of failure: broken/missing housing, loose slider, vent won't adjust or stays stuck

• One humidity control body

• Disconnect power and remove the crisper/bin or cover for access
• Note slider orientation and position before removal
• Transfer the slider to the new body and secure the body to existing mounting points
• Avoid overtightening to prevent cracking; verify smooth slider travel before reassembly

Size: 8 x 1-1/4 inch.

This grommet isolates the refrigerator's fan motor from its mounting bracket to reduce vibration and noise while keeping the motor secure. Replacing worn or missing grommets helps stop rattles and prevents the fan blade from rubbing.

• Cushions the fan motor to maintain proper alignment and clearance
• Absorbs vibration to help reduce humming, buzzing, or rattling sounds
• Helps keep the motor stable so the blade doesn't contact the shroud
• Common signs of failure include excess vibration, noise, or a loose fan motor

• Disconnect power to the refrigerator before servicing
• Access the fan motor area (rear of unit or inside the freezer, depending on model) and support the motor
• Remove mounting hardware and seat the new grommet fully in the bracket/mount
• The fan blade spins freely with even clearance before reassembling and restoring power

Color: Almond

This drain tube gasket seals the connection between the drain tube and its mating port to prevent leaks. A tight seal helps keep water where it belongs and protects surrounding components from moisture damage.

• Creates a watertight seal at the drain tube connection point
• Can help address water leaks around the drain area
• Deterioration, cracking, or hardening of the old gasket may cause seepage
• Replacing a worn gasket can restore proper leak prevention

• Unplug the appliance and shut off water supply before service
• Place a towel or pan to catch residual water when disconnecting the tube
• Inspect the tube and mating surfaces; clean before installing the new gasket
• Do not overtighten fittings; verify a snug, even seal and check for leaks on first run

This nonmetal shim acts as a precise spacer/isolator within an appliance assembly to set correct clearance and alignment between parts. Replacing a worn or missing shim can reduce vibration, prevent rubbing, and help maintain smooth operation.

• Maintains proper spacing between mating parts to ensure correct alignment
• Helps reduce vibration, rattling, and premature wear from parts contacting
• Nonmetal construction provides electrical isolation and resists corrosion
• Common signs of a bad/missing shim: scraping noises, visible misalignment, or excess play at the joint

• Disconnect power and shut off water/gas supplies as applicable before servicing
• Match the new shim to the original thickness/position; some assemblies use multiple shims—reinstall in the same locations and order
• Clean mating surfaces and inspect related fasteners/brackets; replace any distorted hardware
• Tighten fasteners evenly to manufacturer specifications and verify smooth, interference-free movement after reassembly

Replace a damaged or missing freezer basket to restore organized, easy-access storage in your freezer compartment. This basket keeps items contained and properly positioned to support airflow and make loading and retrieval easier.

• Holds and organizes frozen items within the freezer compartment
• Seats on designated rails or locator tabs for secure, level placement
• Helps maintain airflow around stored packages
• Common symptoms: cracked, bent, or broken basket; won't sit level; or missing

• Empty the freezer area and remove the existing basket
• Align the new basket with the rails or locator tabs and lower into place—do not force
• Usually no tools required
• Wear gloves to protect hands from cold surfaces and sharp edges

This right-side adapter bracket mounts to the appliance cabinet and supports the mating shelf, bin, or panel on that side. Replace it to restore a secure fit and alignment when the original is cracked, loose, or missing.

• Secures and supports the component on the right side of the assembly
• Maintains alignment to prevent wobble, sagging, or pop-out
• Helps drawers/shelves operate smoothly when properly fastened
• Common replacement reasons: broken tabs, stripped holes, visible cracks, or missing bracket

• Disconnect power to the appliance before servicing
• Remove the related shelf/bin/drawer to access the bracket
• Reuse original mounting screws and any transferable clips/spacers
• Tighten screws evenly without overtightening

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

This foam-in-place (FIP) gasket creates a tight seal between mating surfaces inside the appliance. A proper seal helps contain conditioned air, reduce moisture intrusion, and support consistent, efficient performance. What it does:

• Forms an air- and moisture-resistant seal between components
• Helps prevent air leaks that can affect temperature stability
• Replaces crushed, torn, or missing foam seals
• Common symptoms of a failed seal: visible gaps, drafts around panels/ducts, persistent condensation or frost near the sealed area, temperature swings

• 1 foam-in-place gasket

• Disconnect power before servicing
• Access the sealed component; remove the old gasket and note orientation
• Clean and dry mating surfaces; install the new gasket without stretching or compressing
• Reassemble and confirm the seal is uniform around the perimeter

Glass shelf that provides a sturdy, flat surface for organizing refrigerator items and maximizing usable storage. Replaces damaged or missing shelves to restore stable support and proper spacing inside the fridge. What it does:

• Provides a stable surface for food containers, beverages and produce.
• Restores correct shelf height and spacing for efficient storage and door/drawer operation.
• Replaces cracked, chipped or broken glass to prevent items from falling or shifting.
• Installs into existing shelf rails to re-establish usable storage area.

• Remove all items from the shelf area and support the glass at both ends during removal and installation.
• Align the shelf with the existing rails and slide evenly until fully seated; do not force.
• Handle broken glass with heavy gloves and dispose of the old shelf safely.

Screw: 8-16 x 3/8 inch.