Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't spin or agitate? A faulty lid switch prevents operation when the lid isn't closed. DIY-friendly repair, typically takes 10-15 minutes.
An online search of the problem (would not agitate or spin) indicated a bad lid switch. Then with model number was able to find an online video on how to change it. Next I opened the washer, like in the video (very easy) and made sure that the lid switch looked like the one I ordered from AppliancePartsPros.com. Of course with the model number it was easy to find the right part. The part arrived in 2 days with no special shipping. What great service! Since, the washer was already open,... Read more
Usually ships within 4 - 14 days
Fix a washer that won't advance through cycles or skips fill/agitate steps. This timer controls cycle sequencing. DIY repair in about 30 minutes.
I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more
Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.
Pulled front panel off. Unbolted and removed top cover. Removed tub trim cover. Removed and replaced gasket and dampers. Put it a back together took about 20 minutes Read more
Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.
Ordered new hose from appliance parts pro. Part came in 2 days. Easy to replace. Read more
10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.
The auger motor failed and wouldn't turn. I replaced the motor and it works without a problem. Make sure you dont throw away the motor boot or buy one if you don't have one. Otherwise, the temperature will freeze up the motor and lead to premature failure. Read more
Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.
Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.
5/16-18 tpt ihw s n
Replaced the Coupling Pulsator, and the Pulsator (short spindle in the center of the washer). The only problem that I encountered was how to remove the short spindle in the center of the washer...my fabric softer is in the center and you need to open that, grab the middle and loosen by turning left. Once that is out you will use a 7/16th socket and remove the entire agitator. Most of the videos show that you pull that straight up to remove - not the short one. There is still a screw to remove.... Read more
Secures washer tub and hoses to prevent leaks and noise. Replace if worn or broken to maintain proper alignment and seal. Verify fit with your model.
I did it Read more
Right-side cabinet end cap for washers. Replaces cracked, broken, or missing trim piece. Restores proper fit and protects internal components.
This washer front panel assembly replaces a cracked, worn, or damaged console face. Restores appearance and provides housing for control buttons.
Concrete counterweight that attaches to the washer tub to stabilize the drum during spin cycles. Replace if cracked, broken, or missing pieces.
This zinc-plated screw secures the power control board and other electrical components inside your washing machine. The specific threading and length ensure proper mounting and electrical grounding of control circuits. Replace this fastener if the control board is loose, vibrating, or if the original screw is stripped or missing.
Left apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, broken, or missing to restore proper panel support.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.